they do make gaskets .030"
Jimmy
On 2/27/2012 9:47 PM, Richard Kinsley wrote:The advantage from what I hear is they have a superior seal. Now if they were thinner that'd really be the icing on the cake. However, I have the Fel-Pro's and they work fine too. So I'd opt not to spend the money unless there was an increase in CR.
Rich Kinsley '64 Dodge Polara 4dr 324 poly w/goodies--
On Mon, Feb 27, 2012 at 12:13 PM, Jimmy Peavy <peaver63@xxxxxxxxxxxxxx> wrote:
Well I thought Cometic advertised they would make gaskets for almost anything.
I have looked and I haven't seen the 318 poly listed, but they may be available.
You'd probably have to call them. 440.352.0100
Looks like .040" is a common thickness. So I'm not sure they would help you with compression.
Jimmy
On 2/27/2012 12:08 PM, Richard Kinsley wrote:Can we get Cometic steel gaskets? I think they would be great but I never figured they would be available for our poly's. What thickness would they be? Where could we get them? The metal ones I had were .024" I believe and the Fel-Pro are about .042ish.
Rich Kinsley '64 Dodge Polara 4dr 324 poly w/goodies========================================================================================================================--
On Mon, Feb 27, 2012 at 10:28 AM, Jimmy Peavy <peaver63@xxxxxxxxxxxxxx> wrote:
I'm not sure of the thickness of the steel or the Fel-Pro gaskets you used or are considering, but have you ever considered Cometic steel gaskets?
Jimmy
On 2/27/2012 8:57 AM, Richard Kinsley wrote:Well I have LeRoar all apart again or rather still. I think I just didn't install the metal gaskets properly. The Copper Coat did not adhere to any surface well at all. It actually seemed to make the whole thing slippery and slimy instead. I think there was actually a coating on the metal gaskets already. They were yellowish but I thought the Copper Coat would still be in order. Too bad there weren't any directions with the gaskets.
I will install my trusty old Fel-Pro composites this time and not worry about it. The new CR will be 9.1 and that will be very fuel friendly. It's also a half point better then before anyway. I'm including some pictures of the dis-assembly.I gotta say the steam cleaning sure spruced it up.
One picture shows the exhaust leak. This was spitting water because it was coming from the cylinder and not the bolt. After re-tightening the exhaust bolts this had stopped. I have found some exhaust bolts loosen after getting up to temp the first time. Even a ways down the road they may need tightening again.
Rich Kinsley '64 Dodge Polara 4dr 324 poly w/goodies--
--
Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
--
--
Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
--
Rich Kinsley '64 Dodge Polara 4dr 318poly w/goodies
--
Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
--
--
Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
--
Rich Kinsley '64 Dodge Polara 4dr 318poly w/goodies
--
Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
--
--
Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
Back to the Home of the Forward Look Network