RE: Head bolt final outcome
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: Head bolt final outcome



What is that product that you use on head gaskets   hylmar?? 

 

From: 1962to1965mopars@xxxxxxxxxxxxxxxx [mailto:1962to1965mopars@xxxxxxxxxxxxxxxx] On Behalf Of Richard Kinsley
Sent: Thursday, January 19, 2012 2:43 PM
To: 1962to1965mopars@xxxxxxxxxxxxxxxx
Cc: Chatroom
Subject: Head bolt final outcome

 

I have been pondering getting new head bolts for some time. ARP has the short ones, $2.81ea, and can make the long ones for about $800-$1200 !!!! They probably have off the shelf studs available but they will not allow me to R&R the heads in the engine bay. 

 

We can get grade 8 bolts that will work for about $75 a complete set. These are just off the shelf standard grade 8 bolts. They are rated at about 150,000 to 155,000psi tensile strength and are basically the same as the stock bolts but are shaped a tad different in that the stock bolts are necked down in the center area. I don't know if that would even matter. 

 

Upon consulting with my machinist and his co-worker they have said the real weak point is going to be the threads in the block. The constant removal and re-torque will stress the internal threads more. They don't like the idea of using after market generic bolts as they have doubts to the quality.So the outcome of this search is that I will re-use what I have been using and be sure everything is clean and properly prepared.

 

I also inquired about the steel head gaskets. On this subject he said they should be fine. He says newer steel gaskets come pre-coated whereas the old originals were bare. Mopar made a head gasket spray that was used on them he said. He thinks it may still be available. I'll see if I can find some of that otherwise I will be coating them with Copper Coat spray.

 

So I finally have a definite direction to go for re-assembly.

 

Rich Kinsley '64 Dodge Polara 4dr 324 poly w/goodies

 

 

 

 

 

 

--
--
Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

--
--
Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.


Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.