Re: rear seat belt install (repost)
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: rear seat belt install (repost)



Scott,
That will work, just afraid that the washers' are not big or strong enough to withstand the impact of an accident. Bigger and thicker (in this case) is better. Even if you do not weld them in, jm2cw

DJ

--- On Tue, 6/28/11, Scott Hinojos <lightsplicer@xxxxxxxxx> wrote:

From: Scott Hinojos <lightsplicer@xxxxxxxxx>
Subject: Re: rear seat belt install (repost)
To: 1962to1965mopars@xxxxxxxxxxxxxxxx
Date: Tuesday, June 28, 2011, 8:45 PM

This is what I bought to go with the belts (which are very nice AND made in the USA) I bought from these guys. http://www.seatbeltsplus.com/product/FHD-1046-2.html

I'm more than a little concerned about welding upside down on sheet metal, because I don't trust my welding skills (very rusty) any more. lol

Nick, I'm not sure if I'll need the backing plates, but I'll keep you in mind. :)

Thanks, all!
~S~

On Tue, Jun 28, 2011 at 8:55 AM, <furyus63@xxxxxxxxxxx> wrote:

I have (4) new in the box RB1 style backing plates available. Let me know if you need them.

 

Nick Tiberio

FuryUs63

 


From: Dodger7998@xxxxxxx
To: 1962to1965mopars@xxxxxxxxxxxxxxxx
Sent: Tuesday, June 28, 2011 9:12:46 AM
Subject: Re: rear seat belt install (repost)

The backing plates can also be bolted in place, here is a pic of some aftermarket type ones
 
 
 
 
In a message dated 6/28/2011 7:17:19 A.M. Central Daylight Time, djohn14296@xxxxxxxxx writes:
Scott,
You will probably have to weld a backing plate 4"x4" around the area where you want to drill the hole. The hole should come through the center of the back plate, plate should be welded to the outside of the floor pans. If the car didn't all eady have them. I f you don't then if your in an accident(god forbid), then the rear passenger(s), mounts will just pull though the floor board.

DJ

--- On Mon, 6/27/11, 62to65mopar@xxxxxxxxxxx <62to65mopar@xxxxxxxxxxx> wrote:

From: 62to65mopar@xxxxxxxxxxx <62to65mopar@xxxxxxxxxxx>
Subject: rear seat belt install (repost)
To: "1962to1965mopars@xxxxxxxxxxxxxxxx" <1962to1965mopars@xxxxxxxxxxxxxxxx>
Date: Monday, June 27, 2011, 11:34 PM

This is a resend of a message Scott sent to a wrong address:

>  Hey folks,
>  So I looked at a couple of links concerning installation of seat
>  belts, and my car doesn't quite jive with what I'm reading about it,
>  at least as far as the expectation of factory mounting points.
http://www.wescoperformance.com/2-point-seatbelt-install.html and
http://1962to1965mopar.ornocar.org/ml-seatbelts.html each mention
>  factory mounting points, and I'm just not finding them in my car.
>  That's fine, though, because all I need to know is, will simply
>  drilling a properly sized hole in a place that makes sense on the
>  floor pan going to work safely?

>  I have the proper hardware, but this sentence has me concerned:
>  "Anchor points for belts must meet the strength load requirements of
>  FMVSS 210." Well, what the heck does that mean to me? lol To wit:
>  "Standard No. 210 - Seat Belt Assembly Anchorages - Passenger Cars
>  (Effective 1-1-68 ), Multipurpose Passenger Vehicles, Trucks, and
>  Buses (Effective 7-1-71)
>  This standard establishes requirements for seat belt assembly
>  anchorages to ensure proper location for effective occupant restraint
>  and to reduce the likelihood of failure. The requirements apply to any
>  component, other than the webbing or straps, involved in transferring
>  seat belt loads to the vehicle structure." OK, does that mean that if
>  I drill holes just about anywhere through the floor, it will be safe?

>  Thanks again! Many more questions to come... ;)

>  ~S~


--
--
Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

--
--
Please address private mail -- mail of interest to only one person -- directly to that person. That is, send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
 
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.


Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.