Re: Inner and Outer Seal failure- Rear end- 64 Plymouth

[Gary Wilson <Gwwilson70@xxxxxxxxx>]

It looks like you did it right.  The only thing that I would do that is
different is I use Vaseline on the outer part of the seal  and also on the
lip of the inner seal.  This makes it slide in easier and helps save the
seal from getting scarred.  Never lost one that way.

On Sun, May 8, 2011 at 4:24 PM, Butch Edison <waedison@xxxxxxxxxxx> wrote:

>
> http://www.picupine.com/2896cc3x-1
> If the link above works, you can view how I went about replacing my leaking
> rear axle seals. If you see any "uh ohs" please let me know. Thanks/Butch
>
>
> -----Original Message-----
> From: Butch Edison [mailto:waedison@xxxxxxxxxxx]
> Sent: Friday, May 06, 2011 1:02 PM
> To: 1962to1965mopars@xxxxxxxxxx
> Subject: Inner and Outer Seal failure- Rear end- 64 Plymouth
>
>
>
> Okay, so when I went through my 64 Sport Fury I got a couple of years ago,
> I rebuilt the rear brakes, put in new rear axle bearings as well as the
> inner and outer seals. The seals I put in leaked, on both sides, ruining the
> brake shoes. I had a difficult time installing the inner seals even though I
> have what I think is the correct Miller driver # ?-839. After ruining a few
> inner seals, I thought I got it right. While taking it all apart today, I
> don't see any apparent problems with the seal faces.
>
> So, I've taken the rear axles out to take a look. when I pulled the first
> axle, I got about 2 cups of rear end oil on the ground. I see that the oil
> is sitting level with the bottom of the seal as it sits in the axle. In
> other words, the axle tube is full of oil up to the bottom edge of the seal.
> Did I simply overfill the rear end when I refilled it? The SM says the rear
> end takes 4 pints, but what does that look like from the end of the axle
> tube ? I used what I thought was the correct rule of thumb when filling it,
> filled it till it touched the tip of my finger with my finger in the fill
> hole, bent at the first joint.
>
> Second, how does the large bearing at the end of the axle get it's
> lubrication? Is it supposed to be bathed in rear end oil, which doesn't
> sound right, as it's sandwiched between the inner and outer seal. Am I
> supposed to pre-grease it and it stays lubed with that, or is some oil
> supposed to get past the inner seal and lube it.
>
> Hope these questions are clear. Thanks/Butch
>
> [Non-text portions of this message have been removed]
>
>
> ----
> Please address private mail -- mail of interest to only one person --
> directly to that person.  I.e., send parts/car transactions and negotiations
> as well as other personal messages only to the intended recipient, not to
> the Clubhouse public address. This practice will protect your privacy,
> reduce the total volume of mail and fine tune the content signal to Mopar
> topic.  Thanks!
>
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and
> http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
>
>
> ----
> Please address private mail -- mail of interest to only one person --
> directly to that person.  I.e., send parts/car transactions and negotiations
> as well as other personal messages only to the intended recipient, not to
> the Clubhouse public address. This practice will protect your privacy,
> reduce the total volume of mail and fine tune the content signal to Mopar
> topic.  Thanks!
>
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and
> http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
>
>
>
>

--
[Non-text portions of this message have been removed]


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.