RE: 273 Swapping Sides on Pistons
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: 273 Swapping Sides on Pistons



When I built the 426 wedge for my 64 Polara 4 years ago I used any tips 
from Don's "Old Reliable" I coud, and one of them was to turn the 
pistons (stock 10-1) 180 degrees. The engine has about 3200 miles on it 
now without any problems, but I can hear some noise on the road. 
However, I think it's something else rattling a little, not the pistons.
65 wrote:
> 
> If you find the article, Dodger, post it on the FABO site, as they wont 
> believe me when I tell them about this procedure. They all think you 
> just 
> switch the piston/rod assembly bank-for-bank.
> 
> Darwin/BC/Canada
> '65 Cdn. Valiant Custom 100 'vert
> --225/A833...in a million pieces
> '67 Dart GT 'vert
> --273/904...in "enjoying" condition
> 
> 
> 
> ----- Original Message ----- 
> From: <Dodger7998@xxxxxxx>
> To: <1962to1965mopars@xxxxxxxxxx>
> Sent: Thursday, January 28, 2010 2:29 PM
> Subject: Re: 273 Swapping Sides on Pistons
> 
> 
> >
> >
> > Ok hope I am not opening a can of dead worms here, but will tell what I 
> > was
> > told many years ago.......
> >    to reduce rotating friction, turn your pistons 180  degrees when
> > installing them,,,,,,,,,,,,,supposedly the story goes like 
> > this,,,,,,,,,the pin
> > in the piston is not dead center, and is designed to create  a very 
> > minimal
> > amount of bind when at top dead center of the stroke,,,,,this is  done 
> > so 
> > as
> > to eliminate piston rattle when the piston is in the process of  
> > changing
> > direction at end of stroke.......... the article that I read  on this 
> > also
> > said that the engine would be noisy compared to the stock build,  but 
> > would not
> > cause harm,,,,,,,if someone is interested I will try to find the  
> > article
> > and post it,,,,,,,,,,,,,,, dodger
> >
> >
> > In a message dated 1/28/2010 12:30:03 P.M. Central Standard Time,
> > stevec@xxxxxxxxxxxxxxxxxxxx writes:
> >
> >
> > Tom,
> > We used to do it on big blocks all the  time (flat tops), but have
> > never tried it on a small block.  We were  always careful not to rev it 
> > to
> > much when the motor was cold but it seemed  that the motors made more 
> > power.
> >
> > SC
> >
> > -----Original  Message-----
> > From: Tom Watters [mailto:tomwatters@xxxxxxxxxxx]
> > Sent:  Thursday, January 28, 2010 12:58 AM
> > To:  1962to1965mopars@xxxxxxxxxx
> > Subject: 273 Swapping Sides on  Pistons
> >
> >
> > Over on the A-Bodies only Board, they are talking about  swapping sides 
> > on
> > the 10.5:1 pistons on 273's.  I had some confusion,  but it seems to 
> > make 
> > a
> > little sense.  Dome offset isnt centered, so  parts of the piston may 
> > come
> > closer to the head in places and more gap in  others.
> >
> > http://www.forabodiesonly.com/mopar/showthread.php?t=84332 (3/4  down 
> > the
> > page is where part of it starts posted by Russ (Double  M).
> >
> > Has anybody on the list done this in the past and had any real  success?
> > What are the downsides to  this?
> >
> > Thoughts?
> >
> >
> > Thanks
> > --Tom
> >
> >
> > ----
> > Please  address private mail -- mail of interest to only one person -- 
> > directly to  that person.  I.e., send parts/car transactions and 
> > negotiations as
> > well  as other personal messages only to the intended recipient, not to 
> > the
> > Clubhouse public address. This practice will protect your privacy, 
> > reduce
> > the  total volume of mail and fine tune the content signal to Mopar 
> > topic.
> > Thanks!
> >
> > 1962 to 1965 Mopar Clubhouse Discussion  Guidelines:
> > http://www.1962to1965mopar.ornocar.org/mletiq.html and
> > http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
> >
> >
> >
> >
> > --
> > [Non-text portions of this message have been removed]
> >
> >
> > ----
> > Please address private mail -- mail of interest to only one person --  
> > directly to that person.  I.e., send parts/car transactions and 
> > negotiations as well as other personal messages only to the intended 
> > recipient, not to the Clubhouse public address. This practice will 
> > protect 
> > your privacy, reduce the total volume of mail and fine tune the content 
> > signal to Mopar topic.  Thanks!
> >
> > 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> > http://www.1962to1965mopar.ornocar.org/mletiq.html and 
> > http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
> >
> > 
> 



Jeff Adams
64 Polara


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html. 












Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.