"Engine Turned" tape vendors

[Douglas Sutherland <pluckedchickens@xxxxxxxxxxx>]

I checked these tape vendors out.  
Here is the problem:  
lategreatchevy.comThe tape offered here is NOT a roll, it comes in 6 pre-cut pieces to match a '62 or '63 Impala SS molding.  '62 Impala trim starts narrow on the front fender and widens as it goes to the rear quarter (opposite of a Sport Fury).'63 Impala has a short narrow molding that does not look even close to a '64 Sport Fury
tapebrothers.comTheir tape comes in 1" or 2" widths. 
'64 Sport Fury trim is 1-3/8" wide at its widest point which means the 2" tape needs to be trimmed down to fit the width AND trimmed to match the taper of the molding.  That calls for some precise trimming.
Another thing is that if you want the trim to match STOCK, there should be two vertical full "engine turned" circles with a 1/2 circle above and below them.  The 2" tape has 2 full and 2 half circles in it, but you have to trim 5/8" off.




> To: 1962to1965mopars@xxxxxxxxxx
> From: spigot2039@xxxxxxxxxxx
> Subject: RE: Engine Turned pattern on '64 Sport Fury side trim
> Date: Thu, 21 Jan 2010 13:09:25 -0600
> 
> 
> 
> Did you see the leads that Jeff Adams sent?
> 
> http://www.tapebrothers.com/ProductDetails.asp?ProductCode=TT814LETS2X10&Show=TechSpecs is one.
> 
> Thanks,
> Gary H. 
> 
> -----Original Message-----
> >From: Douglas Sutherland  
> >
> >tape for a '63 Impala looks too narrow. 
> >I will see if they carry the same thing for a '62 Impala -- that year had more similar molding to a '64's Sport Fury
> >
> >
> >
> >> To: 1962to1965mopars@xxxxxxxxxx
>  
> >> This? 
> >> 
> >> http://www.lategreatchevy.com/product.asp?pf_id=537001&dept_id=1492
> >> 
> >> Thanks,
> >> Gary H.
> >> 
> >> 
> >> -----Original Message-----
> >> 
> >> >Try as I might, I could not find a supplier for the aftermarket tape with machining. If someone has a link or source, please send it along. 
> >> >
> >> >
> >> >
> >> >Good to hear from you Ron! 
> >> >
> >> >
> >> >
> >> >Thanks/ Butch/Ferndale, WA 
> >> >
> >> > 
> >>  
> 
> 
> ----
> Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!
> 
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html. 
> 
 		 	   		  
_________________________________________________________________
Hotmail: Trusted email with Microsoft’s powerful SPAM protection.
http://clk.atdmt.com/GBL/go/196390706/direct/01/
--
[Non-text portions of this message have been removed]


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html. 

This email was sent to: arc.6265@xxxxxxxxxxxxxx

u/?bUrDWg.bSONJP.YXJjLjYy



?p=TEXFOOTER