RE: dash mounted rearview mirror

[Paul Lennemann <pjlenn@xxxxxxxxx>]

I have a pair of 8" needle nose vise grips w/ a 45 degree offset.  Not 
sure it will open that far but it should be close.  I'll try to remember 
to check tomorrow.

Paul L.
'63 Sport Fury
440/727
http://www.1962to1965mopar.ornocar.org/ml-lennemann63.html
  
62pluckedchicken@xxxxxxxxx wrote:
> 
> huh?
> ;)
> I'll go to the hardware store and see what I can figure out..
> 
> I don't really wanna bang too much on it, for fear of shattering a 47 
> year old mirror... bad luck, don't ya know ;)
> 
> Rich Kinsley wrote:
> > 
> > The nut is dished so you could use like a spanner wrench on the inside 
> > of the nut. I built one for a similar situation using 5/16" steel 
> > tubing. Cut off about a 16" piece. Bend it in a U shape. Cruch the ends 
> > in a vise in the right orientation to fit inside the nut. Then spread 
> > the ends to fit tight against the sides and bend a 90deg near the end so 
> > 
> > 
> > you have room and leverage to work it. I think it'll work if you can 
> > understand what I said???? Same could be done with a chunk of narrow 1' 
> > to 2" flat steel about 3/16" thick. You can grind out a notch to fit the 
> > 
> > 
> > interior.
> > 
> > Sticking a screwdriver or punch against it to give it a couple licks to 
> > loosen it may help too.
> > 
> > Rich Kinsley '64 Dodge Polara 4dr 318poly w/goodies
> > =====================================================================
> > 62pluckedchicken@xxxxxxxxx wrote:
> > > 
> > > here's some pics of my frustration...
> > > 
> > > http://www.timelesstransport.com/dashpad-install/
> > > 
> > > Rich Kinsley wrote:
> > > > 
> > > > You're good with pictures. Can you send a pic of the area? I was 
> > > > thinking they might have a tool like you use on doors to use for the 
> > > > mirror. I think maybe you could make one from some 1/8" steel? It'd be 
> > > > an interesting challenge. Also if you have that socket maybe you could 
> > > > cut a thin piece from the socket and have it welded to a thin piece of 
> > > > steel. Let's see what it looks like. I always like to make custom tools 
> > > > :-)
> > > > Rich Kinsley '64 Dodge Polara 4dr 318poly w/goodies
> > > > 
> > > > =====================================================================
> > > > 62pluckedchicken@xxxxxxxxx wrote:
> > > > > 
> > > > > anyone here ever removed a dash mounted mirror on a 62 chysler? 
> > > > > 
> > > > > Is there a trick to this? the nut holding the mirror in place is 1-3/8 
> > > > > inch, making a wrench almost impossible to find that will fit in that 
> > > > > space (through the hole for heater controls)
> > > > 
> > > > 
> > > > 
> > > > Rich Kinsley '64 Dodge Polara 4dr 318poly w/goodies
> > 
> > 
> > 
> > Rich Kinsley '64 Dodge Polara 4dr 318poly w/goodies


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html.