Re: 4-Speed Trans Removal Question
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: 4-Speed Trans Removal Question




That is the way I did mine, with a piece of 2x6 under the rear of the pan and a bottle jack- loosen the front motor mount flare nuts. That way you can control the angle of the engine. I used a floor jack under the tranny , but a tranny jack would be much better..........................MO ......sw iowa ----- Original Message ----- From: "john althaus" <althausjbl@xxxxxxx>
To: <1962to1965mopars@xxxxxxxxxx>
Sent: Saturday, June 13, 2009 9:00 AM
Subject: Re: 4-Speed Trans Removal Question



Dennis, might not be the aproved method, but on my 64 hemi we put a block of plywood under the pan with a jack and controled the rear of the project with that. I do have an aftermarket Milodon pan on the motor. Oh yes we did pull mine complete motor and tranny, I'd never do that again!

John
64 Savoy Hemi. 4 spd
------Original Message------
From: Dennis C.
To: 1962to1965mopars@xxxxxxxxxx
ReplyTo: 1962to1965mopars@xxxxxxxxxx
Subject: 4-Speed Trans Removal Question
Sent: Jun 12, 2009 10:54 PM


I need to pull the 4-speed transmission out of my 63 Sport Fury. I have
a 383 and Borge Warner T-10 in the car. If I had help and more time I
would prefer to remove the transmission and engine together but at this
time it is not an option.  My rear main seal is leaking but that can
wait for now.

I checked the manual and it referred to a fixture to support the rear of
the engine?

I was considering a length of 4"X4" wood with blocks on each end that
would go up to the block castings on each side of the pan and jacking up
the engine.

Is there a better way?

Any suggestions will be appreciated.

Dennis C.

1996 Dodge Ram 3500 Van Conversion
1964 Plymouth Belvedere 318 Auto
1963 Plymouth Sport Fury 383 4-speed
1949 Dodge Pickup 289/C4 soon to be changed
1998 Honda Valkyrie Standard


----
Please address private mail -- mail of interest to only one person -- directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html.



Sent via BlackBerry by AT&T


----
Please address private mail -- mail of interest to only one person -- directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html.


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html.













Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.