Re: Fw: Re: 4 speed firewall reinforcements
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Fw: Re: 4 speed firewall reinforcements



WHEN I TALKEd to brewers a few weeks ago about ordering an over center
spring for my pedal  assembly,( the spring was missing when i bought
the pedals)  , wayne brewer told me with a centeforce  clutch i
wouldnt need it.    I didnt pursue it any further, i took his word for
it and  didnt order it. dont quite understand why  though.
   neal zimmerman, eugene oregon

On 2/8/09, MO ( Steve Mick) <micher@xxxxxxxxxxxxxxx> wrote:
>
>  I am thinking of using the Centerforce clutch.  Not having any experience
> with them, are they about the same as stock in depressing the clutch pedal (
> resistance)?  Why do they say to disconnect the over center spring? To keep
> the pedal from sticking down under high RPM shifts like the old diaphram
> clutches did??...........................MO................SW IOWA
>
> -------Original Message-------
>
> From: Don Gallimore
> Date: 2/8/2009 12:03:13 PM
> To: 1962to1965mopars@xxxxxxxxxx
> Subject: Re: 4 speed firewall reinforcements
>
> In my '65 Belvedere using a Centerforce Dual Friction Clutch, there was
> No difference in the firewall versus an automatic nor did I go to any
> Trouble reinforcing anything. Shifts including pedal to the wall power
> Shifts were problem free.
>
> The only thing I would say was reinforced was that the ball on the
> Fender well side was on a stamped triangular plate held to the body by
> Three bolts. The holes or dimples may be there on the body. The edge of
> The plate was rolled for stiffness, I assume. Plate was about 3" on a
> Side. This is the factory set-up. Check with Brewers if you don't have it.
>
> Akron Don
>
> Neal Zimmerman wrote:
>> Hi guys , been a while , been working a lot on my "off topic" 67 cuda
>> so have been avoiding you. Although I have made some progress on the
>> 62 dart as well.
>> Anyhoo, this could apply to any Mopar 4 speed conversion , so just
>> use your imagination.
>> I am converting the 67 cuda over to a new stout small block and a
>> 4 speed with a Centerforce clutch, so reinforcements are in order I
>> hear.
>> The Z-Bar I have totally reinforced with gussets on both arms , so
>> that's gonna be sufficient and also on the fenderwell where the outer
>> ball stud mounts ( as I hear they like to crack or tear out there).
>> I have also reinforced the pedal assembly to take care of any
>> flexion in the assembly there- but I still hear that the firewall can
>> give u problems. How can u reinforce this area??
>> I am afraid I f I put a plate on the passenger compartment side of
>> the firewall it will throw out the mounting points of the pedal
>> assembly. I could also go on the engine side I guess but will that
>> throw any thing out.
>> I did see a plate on ebay that the guy claimed was a factory
>> original reinforcemnt for factory 4 speed cars , but I cant figure
>> out where the things supposed to go.
>> Help!!
>> Neal Zimmerman, Eugene Oregon
>>
>>
>
>
> ----
> Please address private mail -- mail of interest to only one person --
> directly to that person. I.e., send parts/car transactions and negotiations
> as well as other personal messages only to the intended recipient, not to
> the Clubhouse public address. This practice will protect your privacy,
> reduce the total volume of mail and fine tune the content signal to Mopar
> topic. Thanks!
>
> '62 to '65 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html.
>
>
> .
>
>
>
> ----
> Please address private mail -- mail of interest to only one person --
> directly to that person.  I.e., send parts/car transactions and negotiations
> as well as other personal messages only to the intended recipient, not to
> the Clubhouse public address. This practice will protect your privacy,
> reduce the total volume of mail and fine tune the content signal to Mopar
> topic.  Thanks!
>
> '62 to '65 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html.
>
>


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html. 












Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.