RE: 383 compression
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: 383 compression



Earl, what altitude are you where you live? /Butch /Ferndale, WA 

-----Original Message-----
From: Earl H. [mailto:earlh@xxxxxxxxxxxxxx] 
Sent: Thursday, December 28, 2006 1:24 PM
To: 1962to1965mopars@xxxxxxxxxx
Subject: FW: 383 compression


 

In my opinion the best way to set up a big block Mopar with flat top pistons
is to always zero deck the motor. Of course it is important to pick a flat
top piston with a pin height that lets you do the minimum amount of decking.
Then, you adjust your compression with chamber size and gasket thickness.
Unless you do this you will never be able to take advantage of having a
proper quench area which gives you the ability to control detonation.

I just got thru convincing a friend to tear his motor apart and do this. He
had a machine shop that knew nothing about Mopars set his motor up. The
detonation on his motor was so bad by the time he retarded the timing enough
to get rid of it, no power. It was a 440 with Eddy heads. The pistons were
down in the hole, and he had a Fel Pro gasket. 
At our altitude, this spells detonation. He tried everything under the sun
to no avail. Finally I convinced him to break down the engine, put zero deck
flat tops, with a .045 Comek, put the thing back together. Now it is a
ground pounding 440. With open chamber heads, you don't get as much quench
effect, but it will make the difference in a good engine via a mediocre
engine. If you have a head that gives you a quench area, the rule of thumb
is to have about .035 to .055 quench clearance. The lower the number without
any interference the better. .035 is about as close as you can come with
steel rods, I would suggest .040 just to be safe. Over .055 you start to
loose the sonic boom effect very quickly.

Earl


The low compresion pistons are different and lower in the bore.  or have a
lower compression height if you want the technical term. Now it gets dirty.
too lazy to build a proper piston for both engines  piston maunfactures
fudged the specs for both motors and produced a so called 9 to 1
replacement. piston. Ever seen a 383 redone and it seemed to be ok but
lacking just that something? Well that is why. Even Momma mopars are fudged
them. 
the only real 10 to 1 pistons are the TRW forged replacement pistons. I have
been unable here to find any others. TRW number is L2315F and they like the
original magnms were only "close to 10 to 1 if the heads were in spec. (79.5
to 80 cc. ) Most heads are acually 86 to 91 ccs so even with everything
going your way you could still wind up with 9 to 1 or less even with the
good pistons if you didnt take care of the head thing. Add to that  the
extra 020" for felpros over the original steel shim gasket and your back to
an 8.65 or something to 1 engine with all 10 to 1 parts. if you have the
wrong pistons to start with for example it is possible that even 8 to 1
would be unreachable. 
This is BTW why cc the heads is so important. it doesnt have to be a "super
critical gotta pass tech" job but you need to know how much extra meat you
heads have on them above factory specs.  I use and have for years used a
large cattle siringe for checking them .(In another life (during my career
Sabatical) i was a cattle trucker and feedlot operater "Dolmetsch Beef
Farm")  TSC should have that in stock. You can get a 50cc or 50 ml siringe
and you will have to fill it twice (or get two. ) a dab of dishwashing soap
in your water will keep it from forming a surface tension curve. Then just
screw in a spark plug and level the head and gently squeeze away . Keeping
track. Not fancy but very practical.  The few minutes spent here and the few
dollars spent correcting this alone will yield mountains of burnt rubber and
tire smoke if you are so inclined. 
Don

Author of
Return to Deutschland (True Adventure)
Old Reliable (Mopar)
http://stores.ebay.ca/Don-Dulmage-Enterprises
http://seniordragster.bravehost.com/index.html
[Non-text portions of this message have been removed]


----
Please address private mail -- mail of interest to only one person --
directly to that person.  I.e., send parts/car transactions and negotiations
as well as other personal messages only to the intended recipient, not to
the Clubhouse public address. This practice will protect your privacy,
reduce the total volume of mail and fine tune the content signal to Mopar
topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html. 


----
Please address private mail -- mail of interest to only one person --
directly to that person.  I.e., send parts/car transactions and negotiations
as well as other personal messages only to the intended recipient, not to
the Clubhouse public address. This practice will protect your privacy,
reduce the total volume of mail and fine tune the content signal to Mopar
topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html. 


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html. 

This email was sent to: arc.6265@xxxxxxxxxxxxxx

. 



http://www/?p=








Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.