Re: Inner fender sealing panels.
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: Inner fender sealing panels.



That's good news! The install looks great. 

Thanks for letting us know. 

Gary H.  

>  -------Original Message-------
 
>  
>  OK. I figured it out. See the photos.
>  
>  Mike
>  
>  On 3/26/2023 2:44 PM, 62-65-mail-list-club-Gary-H wrote:
>  > Maybe the attached not-great graphic from the parts book will help?
>  >
>  > If not, maybe hold up the panel with the outer edge of the rubber pointed one way or the other and take a photo to show us the distinction?
>  >
>  > Gary H.
>  >
>  >>   -------Original Message-------
>  >>   From: Jimmy
>  >>  
>  >>   I guess I don't understand the question. I think it will only go one way
>  >>  
>  >>   On 3/25/23, Michael   wrote:
>  >>   > I want to know which way the rubber seal should flex when it is
>  >>   > installed. Should the outer edge of the rubber point toward the tire or
>  >>   > away from the tire while it is pressed against the fender surface?
>  >>   >
>  >>   > Mike
>  >>   >
>  >>   > On 3/25/2023 6:17 PM, Jimmy Peavy wrote:
>  >>   >> Correction. I thought you were talking about something else. The
>  >>   >> recessed part of the panel faces the front of the car
>  >>   >> On 3/25/23, Jimmy wrote:
>  >>   >>> In the  wheel area, towards the engine
>  >>   >>>
>  >>   >>> On 3/25/23, Michael <493mike@xxxxxxxxx> wrote:
>  >>   >>>> Hi fellas and gal,
>  >>   >>>>
>  >>   >>>> I am joyfully assembling my 65 Belvedere for the last time (I hope)! I
>  >>   >>>> need to know which direction the rubber seals on the inner fender
>  >>   >>>> sealing panels face? Should the outer edge of the rubber face into the
>  >>   >>>> wheel area or out toward the hinges and in front, to the front of the
>  >>   >>>> car or into the wheel area? Thanks! My 65 Coronet is different side to
>  >>   >>>> side but, could have had the left fender removed for a rust patch in
>  >>   >>>> the
>  >>   >>>> past. Intuition tells me the edges should face into the wheel area but,
>  >>   >>>> I want it correct.
>  >>   >>>>
>  >>   >>>> Mike
>  > 

-- 
-- 
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
-- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
--- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/1962to1965mopars/20230329225523.53711.qmail%40server309.com.


Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.