Re: front suspension

I didn't remember that?

On Apr 12, 2017 3:05 PM, "Cornelius DeVries" <corneliusdevries@xxxxxxxxx> wrote:

They are riveted in at the factory. You grind the heads off and the new ones come with bolts to replace the rivets. That's what I did when I replaced mine.

Sent from my iPhone

On Apr 12, 2017, at 12:06, 'Paul L. http://1962to1965mopar.ornocar.org/ml-le' via The 1962 to 1965 Mopar Mail List Clubhouse <1962to1965mopars@googlegroups.com> wrote:

Boy is it good to have connections. bt6t4 (George) hooked me up with the ball joint socket and LeRoar (Rich) came down today and brought it, and his best 1/2" impact wrench and we gave it a try. Both uppers came loose easily. What a relief! I had loosened the nut holding the ball joint to the steering knuckle to give it a little room to move if it needed it. I had also dosed them a couple times with a half & half mixture of ATF & acetone over the course of a week or so.

I hadn't ordered any parts as I wasn't sure of being able to get things to come apart. I also wanted to be able to move the car around in the garage and driveway. So I didn't remove anything today. Rock auto has all MOOG parts so the total for uppers & lowers, tie rod ends, and upper control arm bushings, + shipping is $203. Now Lyle if you think you could squeeze another $150 for new UCA's out of my bookkeeper, I'll let you try. But I've got to live with her so in order to keep the eye rolls and the muttering under her breath to a minimum, I'm going to go the Rock Auto route. Plus I do have a 5% discount to apply as well.

I do have one more question. The lower ball joints are shown on the Rock Auto site as part of a one piece casting. Mine are riveted into the LCA. I'm assuming they are originals and the rivets will have to be ground off and driven out. Rich said he didn't remember his being that way. He was thinking the ball joint was a separate piece similar to the uppers.

Again thanks to all who offered knowledge and advice and I say again, good to have MOPAR friends.

Paul L

On Thursday, April 6, 2017 at 8:16:02 PM UTC-5, Paul L. http://1962to1965mopar.ornocar.loosecame org/ml-le wrote:
I took my 63 to the shop today for a front end alignment. I had turned up the torsion bars for more ground clearance. Well they told me I need new ball joints upper and lower and new tie rod ends, plus a radius arm bushing (?). They estimated the job at $1200. I'm thinking I can do most of the work myself and save $$$$. I've priced the parts on Rock Auto and they are probably less than $200. Any pitfalls in doing this work?

Paul L.

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.

--
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.

---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/d/optout.