If it will do you any good I have several flex plates for big block and small block. Would be glad to send you one if you want. Live in Oregon.--On Thu, Apr 16, 2015 at 9:14 PM, Bill M <y1topbanana73@xxxxxxxxx> wrote:--I really hate taking 1 step forward and 2 steps back!!!So I go out tonight expecting the do the last step before putting the engine in...bolt the converter to the flex plate. Unfortunately I figured out the hard way that a "stock" style flex plate has 3/8 bolt holes for the converter. So I pull the engine & trans back apart and drilled then out to the 7/16 needed for the aftermarket converter. NOTE that there isn't much meat in the plate's outside edge after you do that.So I out it back in, bolt up the trans, and figure out the holes JUST BARELY don't match up!! AAARRRGGGHHHH! And if I hog them out more, I'll have slop in the plate and it will likely crack. Now I have to try and find one locally tomorrow if there's any chance of putting the motor in the car on Sat morning. Good #&%!NG luck with that!!!
Bill M
65 Coronet 500 'vert http://goo.gl/6xUS1
73 Dart Sport, 05 Ram 2500 CTD, 4WD, QC, LB, Laramie
21 Model T Depot Hack, 06 Mazda 3
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/d/optout.
--Gwwilson
--
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
--
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.
---
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
To unsubscribe from this group and stop receiving emails from it, send an email to 1962to1965mopars+unsubscribe@xxxxxxxxxxxxxxxx.
For more options, visit https://groups.google.com/d/optout.
Back to the Home of the Forward Look Network