Re: tools questions

[Afterhours Fabrication <afterhoursfab@xxxxxxxxx>]

Lol you're absolutely right. I spent 2 years living in Indiana and loved it!

- Dave

On Sat, Sep 15, 2012 at 6:37 AM, D J <djohn14296@xxxxxxxxx> wrote:
> Yea, but the draw back to living there is, it is still New Jersey, lol.
>
> DJ
> From: Afterhours Fabrication <afterhoursfab@xxxxxxxxx>
> To: 1962to1965mopars@xxxxxxxxxxxxxxxx
> Sent: Friday, September 14, 2012 5:29 PM
> Subject: Re: tools questions
>
> 1) Any 14" cutoff saw I've seen does miters. The go-to saw is the
> Dewalt, by far the best quality and still cheap. I wouldnt use a wood
> saw for cutting metal, it will wreck the bearings quick and the motor
> really isnt up to the task.
>
> 2) I have the HF tubing notcher, works great but kinda sloppy and had
> to shim it a bit to center it up. I use it for odd angles or notches
> in tube that is near a bend. Otherwise I use a Bridgeport mill for
> notches. JD2 makes a nice notcher but quite a bit more than HF.
>
> 3) I have a JD2 Model 3 tubing bender, works great with nice smooth
> bends. I also have a HF pipe bender that I use for schedule pipe, not
> to be confused with tubing. You can get all the dies including square
> for the Model 3, just don't use it often enough for pipe to warrant
> the cost. Protools also makes a nice unit, about the same. Id get
> manual unless you plan on using it often, youll also want to make a
> stand and mount it on the floor with some cement lags.
>
> 4) Like you said, drill presses can be had cheap. A decent one will be
> older, as long as it doesnt have a lot of runout (wobble) it will be
> ok. Walker-Turner brand pops up a lot by me. I use my mill for
> drilling operations but have had a W-T in the past.
>
> 5) Plasmas were mentioned, I run Hypertherm and love it, plus they
> make almost all the torches for other brands so might as well buy from
> the source! TIGs I run Miller Syncrowave and MIG I run Millermatic
> except for my little 110 unit thats a Lincoln MIG-PAK.
>
> PS. I tried to think of something, anything, that costs $125 a month
> out here (NJ) and couldn't think of a single thing. 40x60 building
> will cost you at least $3000 a month if its on a dead end street in
> the ghetto, I'm currently sharing a 1800sqft building that's $3200 a
> month on a main road.
>
> PPS. There are at least 4 Harbor Freights within 15 minutes of my
> location. That's whats good about living here, you don't ever have to
> go far for anything.
>
> - Dave
>
> --
> --
> --
> Please address private email -- email of interest to only one person --
> directly to that person. That is, email your parts/car transactions and
> negotiations, as well as other personal messages, only to the intended
> recipient. Do not just press "reply" and send your email to everyone using
> the general '62-'65 Clubhouse public email address. This practice will
> protect your privacy, reduce the total volume of mail and fine-tune the
> content signal to Mopar topic. Thanks!
>
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and
> http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
> --
> You received this message because you are subscribed to the Google Groups
> "The 1962 to 1965 Mopar Mail List Clubhouse" group.
> http://groups.google.com/group/1962to1965mopars?hl=en.
>
>
>
>
>
> --
> --
> --
> Please address private email -- email of interest to only one person --
> directly to that person. That is, email your parts/car transactions and
> negotiations, as well as other personal messages, only to the intended
> recipient. Do not just press "reply" and send your email to everyone using
> the general '62-'65 Clubhouse public email address. This practice will
> protect your privacy, reduce the total volume of mail and fine-tune the
> content signal to Mopar topic. Thanks!
>
> 1962 to 1965 Mopar Clubhouse Discussion Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html and
> http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
> --
> You received this message because you are subscribed to the Google Groups
> "The 1962 to 1965 Mopar Mail List Clubhouse" group.
> http://groups.google.com/group/1962to1965mopars?hl=en.
>
>
>

-- 
-- 
--
Please address private email -- email of interest to only one person -- directly to that person. That is, email your parts/car transactions and negotiations, as well as other personal messages, only to the intended recipient. Do not just press "reply" and send your email to everyone using the general '62-'65 Clubhouse public email address. This practice will protect your privacy, reduce the total volume of mail and fine-tune the content signal to Mopar topic. Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
-- 
You received this message because you are subscribed to the Google Groups "The 1962 to 1965 Mopar Mail List Clubhouse" group.
http://groups.google.com/group/1962to1965mopars?hl=en.