Polyheads,
Had a nice engine break-in session on the dyno the other day with one of
my 390" Poly Stroker builds.
We made 412HP@5600rpm and 438ft.lbs.torque at 3700rpm. As is common with
the Poly 318 engine the HP and Torque curve was very high and flat.
We averaged 428ft.lbs. of torque from 3400rpm to 5400rpm...now that will
set you back in the seat and keep you there; not bad for a "throw-away"
motor.
Cast iron dual quad w/500cfm Edelbrocks, 9.5compression, Hyd. Poly Cam
with 290/.482" Advertised and 232@.050" , 1.94/1.60" 11/32" Stainless
Valves, a modest head flow of 208/151cfm @.500" lift, 16deg. initial adv.
34total...should make a few more HP and Torque once the rings get used to
their new home.
Gary Pavlovich
----- Original Message -----
From: Shaun & Melynda Rainsbarger
To: 318poly@xxxxxxxxxxxxxxx
Sent: Saturday, April 23, 2011 9:04 PM
Subject: Re: [318poly] Re: "What is that, a 413? A 440?"
Better get out your tape. I replaced a Wrinklehead 318 (another
nickname) with a 440 and it was I think, almost two inches narrower.
Remember, the "A" poly is based on the other earlier polys, that would
swap heads with the same vintage/make hemi. Back then for heads, it was
wider is better. Until sales couldn't pay for the costs.
----- Original Message -----
From: Cory
To: 318poly@xxxxxxxxxxxxxxx
Sent: Saturday, April 23, 2011 6:54 PM
Subject: Re: [318poly] Re: "What is that, a 413? A 440?"
It has something to do with the FACT that the 318 Poly block has the
EXACT same dimensions as the 318 wedge block.
Cory
On 4/23/2011 6:30 PM, belvederetwo wrote:
I know that they've been called that, I was saying that lately I keep
hearing people say they aren't a wide block, or that they were mistakenly
called that. I'm just wondering why people are saying that and where
they're getting *their* information from.
--- In 318poly@xxxxxxxxxxxxxxx, dodger7998@... wrote:
>
> they have been called wide blocks ever since the first LA engines
showed
> up,,,,, they are definitely wider than the LA,,,,, do not have the
exact
> measurements in front of me, but if Rich was around he could tell
you
> exact,,,,,, the poly is almost as wide as the RB Wedges but
narrower than the
> hemi's,,,,,,, do a search on the internet, and look for" wide block
dodge" and
> see what comes up
>
>
> In a message dated 4/23/2011 8:15:32 P.M. Central Daylight Time,
> belvederetwo@... writes:
>
>
>
>
>
>
> --- In _318poly@xxxxxxxxxxxxxxxx (mailto:318poly@xxxxxxxxxxxxxxx) ,
> dodger7998@ wrote:
> >
> > Close,,,,,,,, tell them it is called a Wide block,,,,,,,,,,,,,
>
> Lately, I keep reading things or hearing people say "... it's
mistakenly
> called a wide block."
>
> What's up with that? Someone even told me "it's the same width as
an LA".
>
--------------------------------------------------------------------------
No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1321 / Virus Database: 1500/3593 - Release Date:
04/23/11
__._,_.___
Reply to sender | Reply to group | Reply via web post | Start a New Topic
Messages in this topic (13)
Recent Activity: a.. New Photos 3
Visit Your Group
Switch to: Text-Only, Daily Digest . Unsubscribe . Terms of Use.
__,_._,___
[Non-text portions of this message have been removed]
----
Please address private mail -- mail of interest to only one person --
directly to that person. I.e., send parts/car transactions and
negotiations as well as other personal messages only to the intended
recipient, not to the Clubhouse public address. This practice will protect
your privacy, reduce the total volume of mail and fine tune the content
signal to Mopar topic. Thanks!
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and
http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
Back to the Home of the Forward Look Network