Re: '62 rear drums

[Roger Pettigrew <dodger7998@xxxxxxx>]

what is the asking price?
 
 
In a message dated 3/11/2011 7:25:50 P.M. Central Standard Time,  
lt7dave@xxxxxxxxx writes:

I have  the correct puller and it works.  I don't need it anymore (since I 
went  with a later rearend) if anyone is intersted in it.

Dave

--- On  Fri, 3/11/11, Paul Lennemann <pjlenn@xxxxxxxxx> wrote:

> From:  Paul Lennemann <pjlenn@xxxxxxxxx>
> Subject: RE: '62 rear  drums
> To: 1962to1965mopars@xxxxxxxxxx
> Date: Friday, March 11,  2011, 7:06 PM
> 
> Here is the procedure I use with the correct  puller. 
> Take the axle nut 
> off and put it back on  backwards, turning it so it is flush
> with the end 
> of the  axle.  Attach the puller and tighten it down
> tight using a fist  
> maul.  Then rap the end of center screw with the
>  maul.  Having the nut 
> on backwards ensures that the end of the  axle won't
> mushroom out from 
> all of the pressure.  Doing  this two or three times
> (sometimes just 
> once) will usually  get it to pop loose. and when it comes
> loose it will 
>  pop.
> 
> Paul L.
> '63 Sport Fury
> 440/727
>  http://www.1962to1965mopar.ornocar.org/ml-lennemann63.html
> 
>  62pluckedchicken@xxxxxxxxx
> wrote:
> > 
> > Got your  puller over to Rob.. he's gonna give it a
> shot tomorrow 
> >  morning... keep your fingers crossed ;)
> > 
> >  Thanks
> > Rich Kinsley wrote:
> > > 
> > >  Probably would work but I have one you can
> borrow.
> > >  
> > > Rich Kinsley '64 Dodge Polara 4dr 318poly
>  w/goodies
> > >
>  ======================================================================
>  > > 62pluckedchicken@xxxxxxxxx
> wrote:
> > > >  
> > > > I can't find the puller in Gary's picture,
> but  I did find this on a 300 
> > > > forum  http://www.chrysler300club.com/rcmstuff/fairbanks/puller.html
> >  > > 
> > > > has anyone tried this puller?
> >  > > 
> > > > spigot2039@xxxxxxxxxxx
>  wrote:
> > > > > 
> > > > > 
> >  > > > There's a picture of the type puller
> used shown on the  tech page. 
> > > > > 
> > > > >  http://1962to1965mopar.ornocar.com/images/axlepullertm.jpg
> > >  > > 
> > > > > I don't know if they are still made  but
> I've seen used ones for sale at 
> > > > > swap  meets.
> > > > > 
> > > > >  Thanks,
> > > > > Gary H. 
> > > > >  
> > > > > -----Original Message----- 
> > >  > > >
> > > > > >
> > > > >  >I think he may have made his own
> puller... there is a puller  listed on 
> > > > >  >1962to1965mopar.ornocar.com? 
> 
> > > > >  >
> > > > > >Is it on the Vendor page? 
> >  > 
> > > 
> > > 
> > > Rich Kinsley '64  Dodge Polara 4dr 318poly
> w/goodies
> > >  http://1962to1965mopar.ornocar.org/ml-kinsley64polara.html
> 
>  
> ----
> Please address private mail -- mail of interest to only  one
> person -- directly to that person.  I.e., send
>  parts/car transactions and negotiations as well as other
> personal  messages only to the intended recipient, not to the
> Clubhouse public  address. This practice will protect your
> privacy, reduce the total  volume of mail and fine tune the
> content signal to Mopar topic.   Thanks!
> 
> 1962 to 1965 Mopar Clubhouse Discussion  Guidelines:
> http://www.1962to1965mopar.ornocar.org/mletiq.html  and
>  http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.
>  
> 
> 




--
[Non-text portions of this message have been removed]


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.