Re: ignition and alternator wireing HELP!
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: ignition and alternator wireing HELP!



Thanks Tom , that is a very good wireing diagram, and all who gave me input. 
I think the ignition problem is solved. Thre clue was -the brown wire to the 
ballast resister.   I had checked that  wire. It had a splice terminal on 
the end and no other wire to the other end of the splice. No power from it 
even with the ignition switch on. I thought maybe it only had power when the 
starter was cranking, so I hooked up a remote starter button--No Go. Then 
when I found out the ballast needed a brown wire to it for sure. So--I 
wondered if the starter needed to be cranking with the ignition switch. The 
wifey ran the ignition switch while I tested the brown wire, and 
BINGO. --full 12 volts to it with the starter cranking.  Ran out of time so 
tomorrow I will hook everything up and test again.
Now to figger out the alternator and electronc regulator  issue.  I need a 
simple wireing diagram like the one Tom posted, but for a electronic 
regulator Any more input??Thanks .....................MO
{Steve Mick}
http://stevemick1964dodge.shutterfly.com/pictures/5
----- Original Message ----- From: "Tom Watters" <tomwatters@xxxxxxxxxxx>
To: <1962to1965mopars@xxxxxxxxxx>
Cc: "MO ( Steve Mick)" <micher@xxxxxxxxxxxxxxx>
Sent: Tuesday, February 15, 2011 12:34 PM
Subject: Re: ignition and alternator wireing HELP!


Here's a link to the '65 B-Body wiring diagram.

http://members.cox.net/metalchewy/Tw1020.jpg

Connection to the starter relay would be thru the bulkhead and ignition switch.
On 02/14/2011 11:04 PM, MO ( Steve Mick) wrote:
This is on a 64 Fury 383 with cobbled up under hood wireing.

issue #1-points distributor-wireing to the input side of ballast resister. We know that when engaging the starter, voltage to all systems is reduced. However there is a wire that maintains full voltage even when the starter is cranking . That wire needs to be on the input side of the ballast resister, so that it gets full voltage even when cranking. Where does that wire come from? Through the bulkhead or from the starter relay or???
issue #2 fairly thin , chrome rectangular voltage regulator mounted on 
the firewall with a 2 prong plug on the front side . No other wires. Take 
off the plug and test both prongs on the regulator with the ign. switch 
on , should one of the prongs have power to it?  One prong goes to a post 
on the alternator and the other prong goes to another post on the 
alternator. No other wires to the alternator Shop manual wireing diagram 
is too much for me to make out.
I THINK--the full time 12 volt wire to the ballast resister comes from 
the starter relay, but I cannot  find a ignition switched  connection 
that does not reduce voltage when cranking. HELP!!!......Thanks for any 
input...................MO
.... .
{Steve Mick}
http://stevemick1964dodge.shutterfly.com/pictures/5

----
Please address private mail -- mail of interest to only one person -- directly to that person. I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic. Thanks!
1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

1962 to 1965 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html and http://www.1962to1965mopar.ornocar.com/general_disclaimer.html.











Home Back to the Home of the Forward Look Network


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.