Re: Fw: bALL JOINT BOOTS

[Bill <Y1TopBanana73@xxxxxxxxx>]

${top_text_ad}
Sounds like some gentle nudging with a socket and a BFH is in order.

-- 
Bill M
65 Coronet 500 'vert http://1962to1965mopar.ornocar.com/mmo62008.html
73 Dart Sport, 00 Cherokee Sport, 01 Dakota SLT
21 Model T Depot Hack, 92 Accord, 06 Mazda 3

On Mon, Oct 19, 2009 at 3:19 PM, MO ( Steve Mick)
<micher@xxxxxxxxxxxxxxx> wrote:
>
> My boots are rubber- not poly. They are pliable enough, but the problem is
> there is a hard ring inside the rubber at the large end, and it will not
> stretch.  I can get one side started , but then can't get the other side to
> go on.  Also cannot twist them on over the threads on the balljoint. Maybe
> some lube?. I thought maybe using a peice of tubeing over the boot flange to
> drive it on but didn't want to risk messing up the boot. . Anymore input
> please  Thanks...............MO
> ----- Original Message ----- From: "Jeff Adams" <ledman_70@xxxxxxxxxxx>
> To: <1962to1965mopars@xxxxxxxxxx>
> Sent: Sunday, October 18, 2009 9:19 AM
> Subject: RE: Fw: bALL JOINT BOOTS
>
>
>>
>> A trick us old bikes used to do with old dried out rubber intake boots
>> that wouldn't go over the carbs on our jap bikes was to stick them on a
>> hot bare light bulb for a minute to warm them and stretch them. They
>> won't melt unless you leave them on too long... also, use a lower watt
>> bulb.
>>
>> althausjbl@xxxxxxx wrote:
>>>
>>> If your boots are poly - boil them in water.   Had to do that to get T
>>> bar boots on that were poly
>>>
>>>
>>> John
>>> ------Original Message------
>>> From: Jeff Adams
>>> To: Mopar 62_65
>>> ReplyTo: Mopar 62_65
>>> Subject: RE: Fw: bALL JOINT BOOTS
>>> Sent: Oct 18, 2009 6:22 AM
>>>
>>>
>>> Have you tried shooting them with a little WD-40 Steve?
>>>
>>> Steve Mick wrote:
>>> >
>>> > Try this again.................MO
>>> > ----- Original Message ----- > From: "Steve Mick"
>>> > <micher@xxxxxxxxxxxxxxx>
>>> > To: <1962to1965mopars@xxxxxxxxxx>
>>> > Sent: Saturday, October 17, 2009 5:56 PM
>>> > Subject: bALL JOINT BOOTS
>>> >
>>> >
>>> > > Any Helpful tips on installing the rubber dust boots on
>>> > > balljoints-especially the upper one that has to go over threads. I >
>>> > > > can't
>>> > >
>>> > >
>>> > > get it to ttwist on over the threads by hand. . My boots have a hard
>>> > > ring
>>> > > inside the rubberflange. Can't stretch it.  64 Dodge
>>> > > 440..............................MO
>>> >
>>>
>>>
>>>
>>> Jeff Adams
>>> 64 Polara
>>>

${bottom_text_ad}
----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html.

This email was sent to: ${recipient}

u/?bUrDWg.${encoded_sub_id}.${EMC}