RE: Balanced flywheel

[Jeff Adams <ledman_70@xxxxxxxxxxx>]

I would says that's possible, but I've had 2 different rear ends in the 
car and the car still vibrates.
Steve Mick wrote:
> 
> This is a long shot , but easy to check--do you have a brake shoe 
> dragging? 
> I have had parking brake cables bind from rust-dirt and it sure will 
> cause a 
> vibration.....................MO........sw   iowa
> ----- Original Message ----- 
> From: "Wakeman Massie" <wakey@xxxxxxxxxxx>
> To: <1962to1965mopars@xxxxxxxxxx>
> Sent: Wednesday, March 18, 2009 5:22 PM
> Subject: Re: Balanced flywheel
> 
> 
> >
> > Did you check the rear pinion angle?  It should be parallel to the 
> > trans.ouput and then pointing down a degree or two from there.   I 
> > always 
> > have to mess with that via leaf spring shims to get the vibes to go 
> > away, 
> > particularly if the car is "up" gasser style or slammed low.
> >
> > Just an idea..
> >
> > Wakeman
> >
> > ----- Original Message ----- 
> > From: "Jeff Adams" <ledman_70@xxxxxxxxxxx>
> > To: <1962to1965mopars@xxxxxxxxxx>
> > Sent: Wednesday, March 18, 2009 2:47 PM
> > Subject: Balanced flywheel
> >
> >
> >>
> >> I need some suggestions. I swapped a 413 4-spd into my 64 Polara 5 years
> >> ago in place of a Poly/pushbutton. There was a minor vibration, so over
> >> the last few years I have changed motors, 4-spds, rear ends, 3 different
> >> sets if tires/wheels, 2 different driveshafts, the current one having
> >> been rebuilt and balanced, the front end's been rebuilt and converted to
> >> discs. I STILL have the vibration! The only parts that have not been
> >> changed are the bellhousing and flywheel. AFAIK bigblock flywheels
> >> aren't balanced...correct? The 426 wedge in it now runs smooth at an
> >> idle and revving in the garage. I don't know where else to troubleshoot.
> >> Anybody have any other ideas???
> >>
> >> Jeff Adams
> >> 64 Polara
> >>
> >>
> >> ----
> >> Please address private mail -- mail of interest to only one person --  
> >> directly to that person.  I.e., send parts/car transactions and 
> >> negotiations as well as other personal messages only to the intended 
> >> recipient, not to the Clubhouse public address. This practice will 
> >> protect your privacy, reduce the total volume of mail and fine tune the 
> >> content signal to Mopar topic.  Thanks!
> >>
> >> '62 to '65 Mopar Clubhouse Discussion Guidelines:
> >> http://www.1962to1965mopar.ornocar.org/mletiq.html.
> >>
> >>
> >
> >
> > ----
> > Please address private mail -- mail of interest to only one person --  
> > directly to that person.  I.e., send parts/car transactions and 
> > negotiations as well as other personal messages only to the intended 
> > recipient, not to the Clubhouse public address. This practice will 
> > protect 
> > your privacy, reduce the total volume of mail and fine tune the content 
> > signal to Mopar topic.  Thanks!
> >
> > '62 to '65 Mopar Clubhouse Discussion Guidelines:
> >
> >
> > 
> 



Jeff Adams
64 Polara


----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html.