RE: Help! How to turn stuck motor

[Wade & Landa Lawrence <Lawrence4@xxxxxxxxx>]

[AD removed for archives]
-------------------------------------------------------------------
Are you serious about buying a NEW car or truck soon? 
Research before stepping on the car lot and save THOUSANDS!
Get NO OBLIGATION price quotes from car dealers in your area.
caacKOVb7yoMza/LeadClick
-------------------------------------------------------------------

Kevin:

Hey, this was a great answer, I appreciate the response.  One question
though...what's to keep me from hooking the starter back up and quickly
turning it over with the starter?   I plan on saving the engine (it's a
numbers-matching car), but won't be doing anything with it.  Thanks!

Wade

-----Original Message-----
From: Kevin Merkley [mailto:krmerkley@xxxxxxxxx]
Sent: Tuesday, October 26, 2004 6:09 PM
To: 1962to1965mopars@xxxxxxxxxx
Subject: RE: Help! How to turn stuck motor


[AD removed for archives]
-------------------------------------------------------------------
Are you serious about buying a NEW car or truck soon?
Research before stepping on the car lot and save THOUSANDS!
Get NO OBLIGATION price quotes from car dealers in your area.
caacKOVbNNx9ca/LeadClick
-------------------------------------------------------------------

Hi,

You did not say if you intend to keep the engine or just get it
disconnected from the tranny.

There are many solutions to this problem.

If you do not want the engine:

Pull the tranny off the engine leaving the torque converter on the flex
plate as was sugggested. OR

You may be able to get at as many as three of the flex plate bolts from
the bottom with the inspection plate and starter out of the way.  Then
you may only need the engine to turn just enough to get the last bolt or
two.

In any case, turning the engine over will be hard since if it overheated
and seized, it may be the bearings as well as the rings.

I would pull the heads and soak each cylinder with penetrating oil and
then pound on each piston with a hammer handle.  This needs to be done
with an assistant who is on a johnson bar with a suitable socket on the
crank pulley (1-1/4").  Keep pounding all cylinders and reefing on the
crank nut until the engine turns enough to get at the required flex
plate bolts.

Once the torque convertor is separated from the flex plate, the tranny
can be left in the car and you can pull only the engine or pull the two
together.

It will be easier to try to turn the engine over while it is in the car
than out where it will roll all over the place when you reef on the
crank nut.

Good luck and keep us posted.  We're all in this together.

K.


Lawrence4@xxxxxxxxx wrote:
>
> Gents:
>
> Need some advice:  I'm getting ready to pull the 361 out of my '62 Sport
>
> Fury.  I'm trying to turn the motor over by hand, so I can remove the
> flexplate bolts.  BUT, I can't get it to budge.  A few months ago, the
> motor got overheated and wouldn't run anymore (probably seized up?)  I
> squirted some penetrant down into the cylinders, no luck.  I'm using a
> 1/2" drive long-handled socket wrench (about 18" long).  I don't have an
>
> impact wrench.
>
> Any advice on how to turn this dude over?  Do I need a really long
> breaker bar?  If I remove the heads, is there a way to turn it from the
> top, or at least lube it up some more?  Thanks!
>
> Wade
>
> Wade Lawrence
> '62 Sport Fury Golden Commando



Kevin R. Merkley
Thunder Bay, Ontario
64 Dodge 440 2dr HT (Cdn)

[AD removed for archives]
-------------------------------------------------------------------
Amazing Diet Patch
The fastest - Easiest way to lose weight! Try it now FREE!
caacL7JbNNx9cf/MyDietPatches
-------------------------------------------------------------------

----
Please address private mail -- mail of interest to only one person --
directly to that person.  I.e., send parts/car transactions and negotiations
as well as other personal messages only to the intended recipient, not to
the Clubhouse public address. This practice will protect your privacy,
reduce the total volume of mail and fine tune the content signal to Mopar
topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html.

[AD removed for archives]
-------------------------------------------------------------------
Amazing Diet Patch
The fastest - Easiest way to lose weight! Try it now FREE!
caacL7Jb7yoMzf/MyDietPatches
-------------------------------------------------------------------

----
Please address private mail -- mail of interest to only one person -- directly to that person.  I.e., send parts/car transactions and negotiations as well as other personal messages only to the intended recipient, not to the Clubhouse public address. This practice will protect your privacy, reduce the total volume of mail and fine tune the content signal to Mopar topic.  Thanks!

'62 to '65 Mopar Clubhouse Discussion Guidelines:
http://www.1962to1965mopar.ornocar.org/mletiq.html. 



b7yoMz.