{Chrysler 300} more , some-results, and thinking / coloring a bit over
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

{Chrysler 300} more , some-results, and thinking / coloring a bit over fsm , which was actually quite close



So went through this , we are all thinking.. understanding 
put big vacuum gauge about  4-5" on heater vacuum pin , little ones are useless 
Baseline , would  start  , ok but after 10 -30 sec rpm starts dropping vac too it just stops . 
Inspected carbs all re built  nice job , -- as we will find out plus some good stuff 
1) looking first at vacuum and idle mix  , the screws are in different in/ out  positions ( not good )but I tuned for  highest vacuum --first rpm was too high , justvignore it ;?this adj  wont  be right at later correct rpm   . On each carb,  screws  were out pretty bad , got vacuum  to 20 . was 14, All  four screws show about equal  impact and smooth action . Tells us thstvall 4 are on board, no adjusting screw issues . Note how much vacuum gauge has already told us . 
no more lope or stall at start but way fast .
Started messing with air  valves to slow down rpm not acting  right    , have no idea where they are . Followed FSM , shut off , count turns . found one open 4 turns(!) set both to zero then out   1.5 turns, as past has told me 1 (from fsm ) not enough   . Started up   , idle IS down (0k!!!)   , but vacuum down too   . 
Went around mix settings again going for vacuum major changes in screws like a turn , back to about 18 ( good);? after hitting peak vacuum opened each ~1/4 turn rich , little impact on vacuum ( down slightly).. thinking being a little rich helps the lean issue at transition, less tendency to lean  out / stall  .Far better than " little lean"  , balky . Setting jt perfect to best place exposes you to lean . This is me -- not fsm .     All are same  #  of turns, air valve  still 1.5 . runnin nice x checked rpm 700 , ( Awwright )   way pleasant surprise !! 

Looked at carbs more carefully , almost  no gas out of squirt at small throttle opening movement  . Weird . Linkage tight no lash . Started suspecting  kit / new accell  pump . Lots of designs for those . Moved plunger down very little , off linkage no gas ... ( hmm) . Although meant to control cc volume , noted the 3 holes in actuator , started thinking . At rest, in most aggressive hole ( it was in middle)  gas starts flowing instantly  because it puts pump plunger deeper into gas at  rest Yow.. !!! instant gas! I am sure this will fix off idle stumble at stop sign . Ymmv , way it was here  -- there was pre travel / lash in pump plunger before gas = big lump of air w/o gas , = that oh no , you feel leaving stop sign and then it goes That IS gone 

So into gear at 700 no bang idle 600 in gear , steady , vac a little low but keeps    running ( yes!!)   
Impression very jumpy off line wants to GO !! no bs  at all 
Choke was /is slow going off  , keeps on high idle too long . as John said. Going to weaken that -- not sure you need much fast idle in normal temps with classic car  , not going driving in snow . Fast idle can add to bang . Ill walt a few minutes if real cold to avoid bang every time over fast idle too aggressive ., so you get a bang every  time from cold 
Big big improvement , it is factually near FSM , did not touch   ignition .   
Carb squirter a big deal , vacuum gauge too . You see impact of adjustments  , no way with "set  smooth  idle " instruction of FSM screws were all over the place    
Henry' s point about exhaust gas analyzer being better is true but i don't car about idle AF want it a little rich ( alky gas needs less air st optimal burn  than 1960 gas , or other  way around more gas  ) and a perfect idle AF is on edge of all the problems lean brings . You can richen idle a small bit , wont overdo it w vacuum gauge monitoring . Seat of pants NG 
Thanks for interest .
Ps Don V trans 1-2 chirp , love it,  even not wide open -- nice fast F no more crossed fingers pulling into traffic      
 Thanks to all 
J 

-- 
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
--- 
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion visit https://groups.google.com/d/msgid/chrysler-300-club-international/8C9A4FDD-3863-460E-8074-5C52A4C89CA1%40gradyresearch.com.


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.