RE: {Chrysler 300} Ram tuning
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: {Chrysler 300} Ram tuning



Hi John

I don't know how in depth you know about tuning a car so forgive me if I go over the basics.  A good video comes from a man who knows his stuff, Uncle Tony.  Watch this for some tips.  https://www.youtube.com/watch?v=AS7nWkn3m94 He also points out GM cars often used manifold vacuum at idle...

I used to use a vacuum gauge to set idle screws until I had the chance to use a two-gas analyser.  What an eye opener!  1/16 turn of the screw made a significant difference.  Go to a garage that has one if you can, if you never want to fiddle with those screws again.  Haven't touch the Val for over20 years since doing that.

Obviously check for a vacuum leak.  Can you get a steady 16 to 20 inches at idle? Val gets 20.

My only other thought, if you use a vacuum gauge to set your idle screws, is to try best idle vacuum reading with the car in DRIVE and see if that helps.  Just don't blip the throttle - ha!

Note that a rich mixture will have the vacuum gauge needle swing back and forth.  Lean mixture will have the needle vibrate.  Good mixture will have a needle that doesn't move, just above the point where it starts to show lean.

Good luck

Henry

-----Original Message-----
From: chrysler-300-club-international@xxxxxxxxxxxxxxxx <chrysler-300-club-international@xxxxxxxxxxxxxxxx> On Behalf Of John Grady
Sent: Thursday, 17 September 2026 10:38 PM
To: chrysler 300 club <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: {Chrysler 300} Ram tuning

This is an old subject but years have gone by and those interested in this , some pretty smart guys have gotten in pretty deep ..... I have " tuned " a lot of rams over the years and surprised by variability in final outcome . Despite a lot of effort, some cars kind of fight, you   a few settle in. 
This is not about obvious stuff we all know , it is about things rams do at times. Maybe all times , more or less . And  some on site have really gained significant knowledge over past 20-30 years 
I have one fighting me now    , the constant fight between stable rpm at idle and slamming into gear  and  then stalling. As if idle has no torque if " loaded up" They even  mention this " rough engaging" in user guide on F .  
Part of it is due to unported vacuum to ignition , always full advance at idle . If vacuum drops ,at trans engage,  ( it does) ignition retards = stall    . I mean this is real and anti stall  thing grew out of it, but opening throttle more just off idle drops vacuum more . Thin line  there . And I think design is flat out wrong we have to tune around it .. I was thinking ??? add a small vacuum can and orifice  to slow down advance action , or buy carbs with ported vacuum like every single other car  the world has  . Carl did that his car runs great . AVS calls to me .. 
The second thing is the tendency to stall off a stop sign depending how much you feather pedal . 
It feels like it goes lean momentarily ( remember this is some cars not all) So seems like  carb squirt is either late  to the party with small thrittle motion  startup off idle , not enough gas , or idle mixture wants to be richer than optimal ( as set by vacuum gauge) to cover this transition It us really bad puling into traffic  and car suddenly stalls, adds stress to driving  . This is  tangled around issue 1 I am ignoring warm up issues , another whole thing , but gets into this in first 15 minutes 

Lets call it ole ram guys , philosophy etc . 

Can be made to be acceptable , yes, but really optimal   -- no, not easy  to get to . And how about ignition timing  ? they say "no spec for that  idle timing  with vacuum on , just set with off"  .but it IS on st idle   . And high , ? leading to above sensitivity  to stalling slamming all that  
Deep thinkers on this , insights gained welcome .. 
J

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion visit https://groups.google.com/d/msgid/chrysler-300-club-international/4B6D8450-04D5-4AED-9465-F7E7BDD49EA4%40gradyresearch.com.

-- 
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
--- 
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion visit https://groups.google.com/d/msgid/chrysler-300-club-international/001e01dd46be%24c58e22a0%2450aa67e0%24%40optusnet.com.au.


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.