On Thu, Jun 27, 2024 at 9:26 AM, John Grady<jkg@xxxxxxxxxxxxxxxxx> wrote:Following is just observation , looking for more info ?i read on the HAMB that a starter from a mid 90’s Dakota truck fits alllater mopars , probably post 62 requiring only cutting the copper cable stud which hits the block on some engines , And may fit earlierI think all these variants listed involve slight changes in clocking , block casting interference etc but that the nose of the starter and gear mesh is possibly the same . Makes sense in a way in that starter mounting is to torqueflight not engine . So it meshes with converter gear . There were various designs and electrical power , and getting the weak one happens . 57 dodge stick fits 392 cannot crank it hot Been there . .And there are two “ strengths” of 392 “fit 0k” with solenoid on top that are slightly different length ? Long one stronger ? Dodge has solenoid on firewallThe consensus of the group on HAMB was that the dakota starter had no problems with 600” B blocks etc but fit A blocks too and was physically small , avoiding header issues for them . And it was cheap on rock auto .I bought one but have not finished car to that point , to try it ( 440 ) ,727 “ let’s see” type thing . But Dakota is A block , so fits those too , goes to 54 up hemi etcThe one posted about here is no doubt terrific and I would go that way as a sure thing .But this other path is of interest too .Does anyone know about this ?There was a discussion of slightly different flywheel tooth count by one individual , maybe in context of stick flywheel who said “ It’s wrong according to tooth count , but works fine (!!!!!) .fyi … ymmvOn Jun 26, 2024, at 11:30 PM, Nick Taylor <nicksgaragesd@xxxxxxxxx> wrote:This is the one I'm using on my 300F and other cars.You do have to grind on the adapter ring a bit in one spot and put on longer cables.--On Wed, Jun 26, 2024, 8:13 PM Michael Marmorale <michael@xxxxxxxxxxxxx> wrote:--Hello all I got the G running and driving! Finally.
It is very hard to start when hot, the starter barley turns the motor over. Cranks fine cold, and I just put in a new group 27 battery.
It feels like the starter is tired.
Is there a high torque starter that will bolt onto the bellhousing? I’m running the cast iron torqueflite.
Any recommendations?
Thanks Mike
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/DM6PR16MB3611383CEF7CC8ACFE026BC6B4D72%40DM6PR16MB3611.namprd16.prod.outlook.com.
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CA%2BjApFOjqE16rJ-04rW1zH0e0UwrwZk0jsreYyYazTFz_0iXag%40mail.gmail.com.
--https://groups.google.com/d/msgid/chrysler-300-club-international/4C7659C1-3102-4E57-A42A-0BB58778322D%40gradyresearch.com
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit.
Back to the Home of the Forward Look Network
Archive Sitemap