Re: {Chrysler 300} 300C upper control arm bushing replacement
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: {Chrysler 300} 300C upper control arm bushing replacement



I would look carefully at the brackets. These are bolted to the frame and would determine the amount of wiggle room for the bushing-arm-bushing assembly. It looks like your brackets are too far apart? I would assume that the manual is correct, the bushing flange must be set hard against the boss on the outside of the upper control arm front and rear, and the assembly should fit snugly between the brackets. A dimension must be available somewhere for the distance between the brackets.  Is it like this on both sides of the car?
 
I think it is safe to say that the caster angle will be affected by the fore-aft position of the arm between the brackets. 
 
If the brackets seem OK and there is still too much slop, I'd consider shims (maybe even thick shock absorber washers).
 
-->I think I know why the bushing rubber chewed up and disappeared: I accessed the forwardlook-300 archive search (Thank You Noel). One article says that, after replacing upper and lower bushings, when installing the arms, the arms have to be in the normal position as if the car is sitting on the ground even though the car is on jacks when removing and replacing the arms.
 
This is true for most any control arm, you should never tighten up all the bolts until the car is resting on the ground with full weight.   But I suspect the bushing was chewed up mostly because of this excessive slack you discovered. 
 
--Mike
 
https://www.ebay.com/itm/203384440913
 
On 08/21/2023 2:51 PM EDT Henry A. Mitchell III <hamlll@xxxxxxxxxxxxxx> wrote:
 
 

First pic: I need to replace all the upper control arm bushings on my 300C.

Second pic: I have the bushings and they are the correct diameter and length.

Third pic: the manual says to slam the bushing flange against the outer face of the control arm on both sides of the arm with both bushings facing inward.

Fourth pic: currently there is a considerable space between the bushing flange and the control arm face, with the spacing being different on all four bushings (left arm, right arm, front and back), but the space is roughly, roughly ¼ inch. There is no possibility of pressing the bushing flange against the arm (on both sides) and have the arm fit in the arm brackets, like the book says to do.

The question is: using the bushings, how do I locate the arm in the arm brackets, using that space between the bushing flange and the arm? Is there a specified space between the flange and the arm front and back, left and right. Do I make the spacing the same on all four bushings? It seems like the position of the arm would affect the caster.

By the way, I think I know why the bushing rubber chewed up and disappeared: I accessed the forwardlook-300 archive search (Thank You Noel). One article says that, after replacing upper and lower bushings, when installing the arms, the arms have to be in the normal position as if the car is sitting on the ground even though the car is on jacks when removing and replacing the arms.

 

Henry Mitchell

      300C


Virus-free.www.avast.com

 

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/001501d9d460%248d2150a0%24a763f1e0%24%40mindspring.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/810366244.119220.1692657944839%40connect.xfinity.com.


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.