|
Hi Ron, They are not done yet with sanding it down. I agree on the removal of all of it. Lucky that the shop is located in a place that this time of year has low humidity.
The only problem I have had with paint is year 2 or 3 bubbles which is of course water vapor that was trapped and then released when the body got hot… Your earlier comments about letting the primer dry good is well taken. James From: chrysler-300-club-international@xxxxxxxxxxxxxxxx <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
On Behalf Of Ron Waters James – Two other suggestions I’d like to offer: In your photos, I see traces of old primer/paint/bodywork that have not been removed. I recommend that every bit be removed
to avoid compatibility problems, which could eventually result in paint lifting. Also, your car is sitting in bare metal. While the shop could be set up to keep humidity on the low side, I still recommend getting the car into epoxy primer as soon as possible
to avoid early rust forming. Ron From:
chrysler-300-club-international@xxxxxxxxxxxxxxxx
On Behalf Of william ELDER James Good advise from Ron about the length of time that a good durable paint job may take, even for a driver quality finish. I see that your K has a front mount radio aerial. If you have any thoughts about adding a right
side exterior rear view mirror, I would go to the Club Tech Page and review Bob Merritt’s video on the subject. The problems arise, when you want to achieve symmetry between the factory installed left mirror and the right mirror. Even the factory installed
left mirror placement has a lot of variation from car to car. There is even more variation when it comes to the dealer installed placement of the radio antenna. I would take measurements and make sure that you will not have an interference problem between
the mirror and the aerial. Now is the time to move the aerial, if you have to, while the car isn’t even in primer yet. Regards bill From: 'James Douglas' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
I went to the body shop today to see how the work is going. The caved in driver’s door was warmed up and carefully hit and a good part of the cave in popped – hammered out thanks to metal memory. The guy who hit it will be paying, via his
insurance, of that work and painting the driver’s side. I will of course pay for the rest of the car. We decide to tell the body shop to sand down the entire car for a complete repaint. With the roof in need of paint and the trunk as well and down the entire left side to get the door to match…there was no way to “conserve the factory paint
job”. Too bad, I had intended to do that. The rest of the body looks as good as new. Truly, zero rust anyplace. Around the rear windows where they used lead at the factory to go over the body welds to the door bottoms to the sills. Nothing but nice clean bright metal with a slight
gray dull look at the lead seams. The fundamental reason I purchased this particular car was the metal. I got lucky, no surprises. Given that the metal is so good and the front and rear glass is not leaking, I elected to leave them alone. I doubt there is anything rust
wise going on under the seals. In any event, I put some rust converter down into the body seal area just in case. I also left the header stainless alone as the side windows are fitting well. I did not want to mess with it. My body guy says he will use an
very small air brush to get down into the roof gutter with the stainless roof gutter trim masked off. For a street car, should be fine. The only damage prior to the drivers door incident was an old repair to the left rear corner. I suspect that the bumper got hit and pushed into the body. The bumper must be a replacement as it shows no sign of it. Whoever did the work on
the body though was an amateur. They just hit it with a pick hammer and pushed it in and used Bondo. My guy will fix it correctly. In about two weeks I should have the car back and ready to put all the bright work back on. Of course, the bright work will now look like crap with new paint
😊 For a driver, I do not know if I want nice chrome or not… James -- -- -- For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang --- You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group. To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx. To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CY5PR19MB6171229842C39B615DF3D9AF9310A%40CY5PR19MB6171.namprd19.prod.outlook.com. |
Back to the Home of the Forward Look Network
Archive Sitemap