First thing is to gain a thorough understanding of how the rubber locks by folding into itself. You need to unlock it with a nylon drift. Never use a metal tool.
Everything, including the seal-to-gasket area, should be soaked in a slippery penetrant, like WD-40 or PB Blaster. Once you get it unlocked, use the drift to wiggle the glass loose from the gasket. Every area of the glass must be free from the gasket. Then
begin to push from the lower third of the glass, where it begins to curve. Just light pushes as it begins to release. It will free up and pop out.
Be sure to read the shop manual for additional instructions. When reinstalling, start from the top edge then the sides, and finally the bottom. Use the nylon drift
to help you out. This is a two person job, BTW.
Again, DO NOT cut the gasket.
Ron
Hi Ron,
I haven’t removed the glass yet, I need to do some slight rust repairs around the rear screen. I’m concerned with getting the glass out without breaking the glass so thought I would cut the rubber.
The front shield I wanted to clean up the edges for painting, but I think I will leave it alone after hearing that.
Any hints on removing rear glass?
Wayne
From:
chrysler-300-club-international@xxxxxxxxxxxxxxxx <chrysler-300-club-international@xxxxxxxxxxxxxxxx> on behalf of Ron Waters <ronbo97@xxxxxxxxxxx>
Date: Wednesday, 4 January 2023 at 2:07 PM
To: Wayne Bakewell <wayne@xxxxxxxxxxxxxxxxxxxxx>, chrysler-300-club-international@xxxxxxxxxxxxxxxx <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: RE: {Chrysler 300} 57 300c windshield rubbers
Here's the deal: You can't. They are not reproduced. The repro stuff you see from 'major vendors' is junk. It's generic and doesn't work. If yours is in fairly good
shape, recondition it. If someone along the way expedited glass removal by cutting the rubber, that was a major mistake. So here's what can be done: For the windshield, understand that it's a W451, which means that any Mopar 2dr hardtop or 4dr hardtop from
1957, except Imperial, also uses the same gasket. Also, 1958 Plymouth hardtops retained the W451 windshield while the other makes went to the later W453. So you have to get one from a parts car. Regarding the rear glass, any senior model 2dr HT that has the
large rear window will use the gasket that you need.
Are these very desirable candidates for reproduction ? YES !
Ron
From: chrysler-300-club-international@xxxxxxxxxxxxxxxx [mailto:chrysler-300-club-international@xxxxxxxxxxxxxxxx]
On Behalf Of Wayne Bakewell
Sent: Tuesday, January 03, 2023 7:11 PM
To: chrysler-300-club-international@xxxxxxxxxxxxxxxx
Subject: {Chrysler 300} 57 300c windshield rubbers
Hi,
I am wanting to know where I can buy new front and rear windshield rubbers for our 57 300c.
Regards,
Wayne
--
For archives go to
http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to
chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit
https://groups.google.com/d/msgid/chrysler-300-club-international/SYCP282MB0207E2648A7F098DC89DDD18EDF59%40SYCP282MB0207.AUSP282.PROD.OUTLOOK.COM.
--
For archives go to
http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to
chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit
https://groups.google.com/d/msgid/chrysler-300-club-international/553C41A4C9F948BB90E16AA44FDE66EC%40ThinkPadL520.
--
For archives go to
http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to
chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit
https://groups.google.com/d/msgid/chrysler-300-club-international/SYCP282MB0207376CDC0A3FC75020C0E5EDF59%40SYCP282MB0207.AUSP282.PROD.OUTLOOK.COM.
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to
.
Back to the Home of the Forward Look Network
Archive Sitemap