Re: {Chrysler 300} valve lash adjustment hemi
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: {Chrysler 300} valve lash adjustment hemi



That decal came with the purple shaft Mopar Performance (formally Direct Connection) cams back in 80’s and 90’s. 

Ryan Hill

On Feb 12, 2021, at 2:55 PM, rob bohuslav <sonoramic413@xxxxxxxxx> wrote:

Bob,

I'm thinking big block (looks to be from a site for big blocks). I believe a big block and small block have the same firing order. I believe the distributor rotation is different, but not sure that matters with cam timing, only at the distributor?


Rob



On Fri, Feb 12, 2021 at 5:45 PM Bob Jasinski <rpjasin@xxxxxxxxxxx> wrote:

Thanks for posting this Rob.  It would be good to know what engines this applies to.  Small block and big block?  CW and/or CCW distributors?

 

Bob J

 

From: chrysler-300-club-international@xxxxxxxxxxxxxxxx <chrysler-300-club-international@xxxxxxxxxxxxxxxx> On Behalf Of rob bohuslav
Sent: Friday, February 12, 2021 11:58 AM
To: John Grady <jkg@xxxxxxxxxxxxxxxxx>
Cc: Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: Re: {Chrysler 300} valve lash adjustment hemi

 

Not sure if this helps..... but this was an old decal that was used and stuck under the hood of many a Mopar back in the day:

 

<image002.jpg>

 

On Fri, Feb 12, 2021 at 2:48 PM John Grady <jkg@xxxxxxxxxxxxxxxxx> wrote:

Without overly complicating it,I was starting to do this and laid out firing order 392  vs crank degrees. 413 the same firing order , but distributor turns CCW other is CW . My new damper marked every 90 degrees.

 

392 and A block;( B may be in the same situation, but not there today).  Starting with #1, at TDC firing (which position by the way is 360 of crank rotation AWAY  (forward CW) from where you align timing chain dot marks..(=confusing as hell , I have ever seen that fact talked about) . Yes , The piston is on TDC when chain  marks are aligned ( at install ) , cam key points at about 4 o clock but that is not the compression or firing stroke. On firing stroke on #1 , the dot on cam sprocket is at  top (180 more  on cam--SO, on next full rotation  of engine ---and firing , yes pointer is back at TDC----.and cam has turned one half turn. #1 Piston went down and came back up. Fire!

 

So, I started overthinking again. ---- on a V8 , 4 firing TDC's  happen per turn of crank, 360/4 = every 90 degrees. So, measured degrees  from the  #1 firing TDC   . 1,8,4,3.  =0, 90, 180, 270 ; 360 position (start of next turn) is the start of 6,5,7,2 firing ,and yes #1 is at TDC again at 360 but not firing ; 360,450,540,630. So 720 is 0 again ,same as # 1 firing . 720 Crank degrees. that is = 360 distributor and cam degrees , rotor is back pointing at 1.  = 18436572

 

Now all through Mopar land is some kind of chart ( I  have a copy) saying adjust I 2 and E 8 when # 1 is at TDC on compression / firing stroke , = still requiring 8 bumps of crank by 90 each , to do 16 valves  . I do not get this advice from on high at all. If #1 is firing on TDC by definition both valves are closed, that is when to adjust #1 valves ? Especially if moving it 8 times anyway.  There is probably some pattern where one could move only 4 times, and adjust say 4 at once, why this line of inquiry started in the first place (from me). But instead sometimes 40 posts in an  online sequence with guys killing each other over how to do this, but none of them advocate what I just said. They confuse themselves with the base circle and " heel" (??) of cam etc . Tangled in underwear? Base circle is a long time % duration of cam, certainly where both lifters  are sitting when cylinder fires?

 

Wha???? is my reaction. Anyone with me? Thoughts?? "for those who do not understand, no explanation suffices" is my reaction to all this, but maybe I am missing something important!???? If so, not alone.. 

 

Best, John G 

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CABZ1P2AUQFQhfEWpULz4p3p0ZhY7FEeRYr%2B0D%2BU482a1nVQkSA%40mail.gmail.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CAGQfsuGJ-EthzhSqO-yPW5Hb5PRZLfsVy1wpDS3O9p-z4cOBmw%40mail.gmail.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/CAGQfsuG12MTWST%3DUkKpopFG%3DCZeCPRRhbrqi8uc%3DxKd8Wg8t8w%40mail.gmail.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/MW3PR16MB3932C4A7BBA5344198CEB154C58B9%40MW3PR16MB3932.namprd16.prod.outlook.com.

JPEG image



Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.