Mild heat too if car not newly painted -propane - put blue tip of flame on screw as long as prudent , then very large Philips screwdriver sharp rap with hammer . You do have the big size screwdriver right ? Forget it with the usual #2 . Fought this on trunk latch once , 57? Sent from my iPhone not by choice > On 17 Feb 2020, at 2:39 pm, finsruskw@xxxxxxxxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote: > > Removing the rear seat ¼ panel will give access to the threads on the back side of the door jamb. > > Try some rust penetrant there. > > Have you already screwed up the Phillips slot/s ?? > > If so, try center drilling the screw so the driver will sit deeper. > > I probably have some used screws to replace damaged ones assuming you can get them out. > > Good luck! > > > > From: Chrysler300@xxxxxxxxxxxxxxx <Chrysler300@xxxxxxxxxxxxxxx> On Behalf Of Cox Scooter465@xxxxxxx [Chrysler300] > Sent: Monday, February 17, 2020 1:23 PM > To: dave.dumais@xxxxxxxxx > Cc: Chrysler 300 List <Chrysler300@xxxxxxxxxxxxxxx>; bob@xxxxxxxxxxxxx > Subject: Re: [Chrysler300] Door pillar strikers > > > > > > I would try a steel head Phillips screw driver. > > Give each screw some > > Heavy strikes. It will break > > Rust loose from threads > > May work. > > > > Bob Haag > > > > > > On Feb 17, 2020, at 12:47 PM, Dave Dumais dave.dumais@xxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote: > > > > Need help on the Coupe door pillar strikers. > > > > 3 Philips head screws, even an impact driver won't crack them loose. > > > > Any experience or suggestions? > > The door is adjusted for gaps. > > But, it will not shut into striker by 3/16. > > > > Thanks, > > > > Dave > > Sent from Yahoo Mail on Android <https://overview.mail.yahoo.com/mobile/?..src=Android> > > > > > > > > > > > [Non-text portions of this message have been removed] > > > > ------------------------------------ > Posted by: <finsruskw@xxxxxxxxxxxxxxx> > ------------------------------------ > > To send a message to this group, send an email to: > Chrysler300@xxxxxxxxxxxxxxx > > To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or > go to https://groups.yahoo.com/neo/groups/all/manage/edit > > For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm > > For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang > ------------------------------------ > > Yahoo Groups Links > > > ------------------------------------ Posted by: John Grady <jkg@xxxxxxxxxxxxxxxxx> ------------------------------------ To send a message to this group, send an email to: Chrysler300@xxxxxxxxxxxxxxx To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or go to https://groups.yahoo.com/neo/groups/all/manage/edit For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang ------------------------------------ Yahoo Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/Chrysler300/ <*> Your email settings: Individual Email | Traditional <*> To change settings online go to: http://groups.yahoo.com/group/Chrysler300/join (Yahoo! ID required) <*> To change settings via email: Chrysler300-digest@xxxxxxxxxxxxxxx Chrysler300-fullfeatured@xxxxxxxxxxxxxxx <*> To unsubscribe from this group, send an email to: Chrysler300-unsubscribe@xxxxxxxxxxxxxxx <*> Your use of Yahoo Groups is subject to: https://info.yahoo.com/legal/us/yahoo/utos/terms/