On Tuesday, May 28, 2019, 1:44 PM, 'John Grady' jkg@xxxxxxxxxxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:
Yes, AMC used doughnuts on Gremlin 6, I had one new for wife. Every 10k-15k miles a leak started . Quickly gets worse.
Maybe a mechanic tried to put one on a 300----head pipe on Mopar has to be bent right, square to manifold flange , and attached firmly with hard gasket, it generally never leaks there. Today’s high end gaskets tend to be a metal matrix for that.. Much better than yesterday’s. Maybe a patch job was done with donuts due to slightly incorrect head pipe flange bend? I took to using one size down stainless bolts and nuts on far side rather than the exhaust manifold tappings –you know why. While on this never ever hang exhaust pipes from exhaust manifold flange while working on it, or installing it ; head pipe alone might be ok, but issue is the bolt flange WILL snap off the manifold if you hang mufflers etc by head pipe, and then try to move around. Pipe has a lot of leverage on that small flange. . Ram F exhaust manifold was the victim, , of course, ----cannot be had anywhere.
From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On Behalf Of Scooter465@xxxxxxx [Chrysler300]
Sent: Tuesday, May 28, 2019 1:25 PM
To: Carl
Cc: Mark Lindahl; Chrysler300@xxxxxxxxxxxxxxx
Subject: Re: [Chrysler300] '63 Chrysler 300 Conv. - 413 donut gaskets between exhaust manifold and pipes.
Doughnut gaskets are a ChevyThing. Mopar used flat steel
Gaskets big blocks. Or ball
And socket flange small blocks.
Ball and socket is the best no
Gaskets to burn out.
Bob Haag
Sent from my iPhone
On May 28, 2019, at 12:10 PM, Carl cbilter@xxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:
Hi Mark, the original part number was Mopar 1855029 and they were all metal gaskets. Current inexpensive replacement part is Fel Pro 9547 or equivalent, but probably not metal. Mancini Racing or one those outfits probably has metal ones which will last longer; just make sure it has a 2.25” center hole and 3.5” bolt hole spacing to fit the exhaust. Might be other Mopar part numbers that fit as well; same size gasket was used on many big block Mopars.
Carl
From: 'Mark Lindahl' mplindahl@xxxxxxxxxxxxx [Chrysler300]
Sent: Tuesday, May 28, 2019 10:29 AM
To: Chrysler300@xxxxxxxxxxxxxxx
Subject: [Chrysler300] '63 Chrysler 300 Conv. - 413 donut gaskets between exhaust manifold and pipes.
Hello All,
I have a ’63 300 Conv, formerly with a 383, now 413 with dual exhausts. The exhaust system has been the same for 29 years since I purchased the 300, with both 383 and 413 engines.
In the past, I have had a local muffler shop install what they called “donuts” between the exhaust manifold and the exhaust pipes. This helped with reducing noise, but also kept the pipes from shaking and hitting the torsion bars, etc.
Now, I am looking for a part number or source to get these “donuts”. Over time, they needed to be replaced since I believe they get crushed. I do not see them listed in the shop manual. Any information would be helpful. Thank you.
Regards,
Mark Lindahl
’63 300 Conv.
PS – I assume this would be the same exhaust set up for 300K 413 non-RAM engine.
[Non-text portions of this message have been removed]
__._,_.___
Posted by: Val Jeffers <edward1108@xxxxxxxxx>
To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx
To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to https://groups.yahoo.com/neo/groups/all/manage/edit
For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang