Exactly Bob! Where I am too. Thanks for the comeback. Maybe now in 2015 it gets settled. I personally think it was done both ways, just from experience, but have nothing to validate that. We might look at old photos when cars were new ,see what we can see. Why I say both ways, I have seen a car with a formed clip that holds the two hoses, attached to a ram bolt I think? . But someone trying to do it right might have taken it from another car . For sure I have a very low mileage F from factory , purposely never touched anything on it for 30+ years, the old I'll get to it someday thing. Correct Terra cotta color on it too..which is a similar thing. Lots of variations on that.. Have a great holiday too! John From: Bob Jasinski [mailto:rpjasin@xxxxxxxxxxx] Sent: Monday, December 21, 2015 1:32 PM To: 'John Grady'; 'chrysler300@xxxxxxxxxxxxxxx Club' Subject: RE: [Chrysler300] RE: 300 G heater hoses John et al, The 300G heater hose routing has been something I have not been able to pin down as correct as long as I've had my G, and that is many years. I have period photo's of 300G engine compartments that show the hoses installed above the intakes, no copper, just hoses, in two configurations, one going around the air cleaner and one through the middle, in addition, I have another photo that shows them underneath the intakes. Hard to tell though, if there is copper there, I suspect there is. Happy Holidays!!! Bob J From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On Behalf Of 'John Grady' jkg@xxxxxxxxxxxxxxxxx [Chrysler300] Sent: Monday, December 21, 2015 10:00 AM To: 'Robert Augliera'; 'David Schwandt'; 'Jerry Lindsay'; 'chrysler300@xxxxxxxxxxxxxxx Club' Subject: RE: [Chrysler300] RE: 300 G AHA!!! Brings up the copper lines. Were they on all F/G cars? I have had a few for sure untouched F with them, I see many at club meets without them. I have a few without them, but replacement hoses. All original hoses are pretty much gone now? Anyway? I think replaced in early days. At least some had copper taken off, hose run end to end. Just a service job in 60's. Hot topic w George, in the way back. And whether under the rams w one hose, if hoses were stock. The clip on some cars says two hoses. . Maybe settled long ago, but still up in air for me.. -----Original Message----- From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On Behalf Of Robert Augliera raugliera@xxxxxxxxxxxx [Chrysler300] Sent: Monday, December 21, 2015 12:37 PM To: David Schwandt; 'Jerry Lindsay'; 'chrysler300@xxxxxxxxxxxxxxx Club' Subject: RE: [Chrysler300] RE: 300 G There is a few pre-bent hoses off water pump housing. Not sure if 5/8 hose will make that tight bend into copper lines From: David Schwandt [mailto:finsruskw@xxxxxxxxxxxxxxx] Sent: Monday, December 21, 2015 11:24 AM To: 'Jerry Lindsay' <jerrylindsay300h@xxxxxxxxxxxxxxx>; Robert Augliera <raugliera@xxxxxxxxxxxx>; 'chrysler300@xxxxxxxxxxxxxxx Club' <Chrysler300@xxxxxxxxxxxxxxx> Subject: RE: [Chrysler300] RE: 300 G Good point, Jerry I recall than now as well. Might be worth looking into. Maybe the club or a member could get a decent price break on a bulk order and make it available to the members. I'd be in for at least 3 cars worth Dave Schwandt From: Chrysler300@xxxxxxxxxxxxxxx <mailto:Chrysler300@xxxxxxxxxxxxxxx%3cmailto:Chrysler300@xxxxxxxxxxxxxxx> <mailto:Chrysler300@xxxxxxxxxxxxxxx> [mailto:Chrysler300@xxxxxxxxxxxxxxx] On Behalf Of 'Jerry Lindsay' jerrylindsay300h@xxxxxxxxxxxxxxx <mailto:jerrylindsay300h@xxxxxxxxxxxxxxx%3cmailto:jerrylindsay300h@tampabay. rr.com> <mailto:jerrylindsay300h@xxxxxxxxxxxxxxx> [Chrysler300] Sent: Monday, December 21, 2015 10:21 AM To: 'David Schwandt'; 'Robert Augliera'; 'chrysler300@xxxxxxxxxxxxxxx Club' Subject: RE: [Chrysler300] RE: 300 G I believe I was told one time that my "H"'s ribbed heated hoses are the same as those used on a corvette, which I believe are still available. Perhaps one of our club members with better knowledge of this subject can better answer it. Jerry Lindsay From: Chrysler300@xxxxxxxxxxxxxxx <mailto:Chrysler300@xxxxxxxxxxxxxxx%3cmailto:Chrysler300@xxxxxxxxxxxxxxx> <mailto:Chrysler300@xxxxxxxxxxxxxxx> [mailto:Chrysler300@xxxxxxxxxxxxxxx] On Behalf Of 'David Schwandt' finsruskw@xxxxxxxxxxxxxxx <mailto:finsruskw@xxxxxxxxxxxxxxx%3cmailto:finsruskw@xxxxxxxxxxxxxxx> <mailto:finsruskw@xxxxxxxxxxxxxxx> [Chrysler300] Sent: Monday, December 21, 2015 10:59 AM To: 'Robert Augliera'; chrysler300@xxxxxxxxxxxxxxx <mailto:chrysler300@xxxxxxxxxxxxxxx%3cmailto:chrysler300@xxxxxxxxxxxxxxx> <mailto:chrysler300@xxxxxxxxxxxxxxx> Club Subject: RE: [Chrysler300] RE: 300 G Kit??? It's 5/8" standard heater hose. I doubt if you can find the older ribbed style Just make sure it's black and you'll be fine. Unless you Club concourse the car, no one will know the difference Goers has the correct corbin style clamps in a 'kit' And pick up the correct style batt hold down and use a black battery and your engine compartment will look about as stock as it can get. Good Luck!! From: Chrysler300@xxxxxxxxxxxxxxx <mailto:Chrysler300@xxxxxxxxxxxxxxx%3cmailto:Chrysler300@xxxxxxxxxxxxxxx> <mailto:Chrysler300@xxxxxxxxxxxxxxx> [mailto:Chrysler300@xxxxxxxxxxxxxxx]<mailto:[mailto:Chrysler300@yahoogroups. <mailto:[mailto:Chrysler300@yahoogroups.%0bcom]> com]> On Behalf Of Robert Augliera raugliera@xxxxxxxxxxxx <mailto:raugliera@xxxxxxxxxxxx%3cmailto:raugliera@xxxxxxxxxxxx> <mailto:raugliera@xxxxxxxxxxxx> [Chrysler300] Sent: Monday, December 21, 2015 9:36 AM To: chrysler300@xxxxxxxxxxxxxxx <mailto:chrysler300@xxxxxxxxxxxxxxx%3cmailto:chrysler300@xxxxxxxxxxxxxxx> <mailto:chrysler300@xxxxxxxxxxxxxxx> Subject: [Chrysler300] RE: 300 G Cummins red it is. Is there a heater hose kit available Thank you Rob From: Robert Augliera Sent: Monday, December 21, 2015 10:03 AM To: 'chrysler300@xxxxxxxxxxxxxxx' <chrysler300@xxxxxxxxxxxxxxx <mailto:chrysler300@xxxxxxxxxxxxxxx%3cmailto:chrysler300@xxxxxxxxxxxxxxx> <mailto:chrysler300@xxxxxxxxxxxxxxx>> Subject: 300 G Any suggestions for the color red used on intakes. Rob [Non-text portions of this message have been removed] [Non-text portions of this message have been removed] ------------------------------------ Posted by: Robert Augliera <raugliera@xxxxxxxxxxxx> ------------------------------------ To send a message to this group, send an email to: Chrysler300@xxxxxxxxxxxxxxx To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or go to https://groups.yahoo.com/neo/groups/all/manage/edit For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang ------------------------------------ Yahoo Groups Links [Non-text portions of this message have been removed] ------------------------------------ Posted by: "John Grady" <jkg@xxxxxxxxxxxxxxxxx> ------------------------------------ To send a message to this group, send an email to: Chrysler300@xxxxxxxxxxxxxxx To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or go to https://groups.yahoo.com/neo/groups/all/manage/edit For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang ------------------------------------ Yahoo Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/Chrysler300/ <*> Your email settings: Individual Email | Traditional <*> To change settings online go to: http://groups.yahoo.com/group/Chrysler300/join (Yahoo! ID required) <*> To change settings via email: Chrysler300-digest@xxxxxxxxxxxxxxx Chrysler300-fullfeatured@xxxxxxxxxxxxxxx <*> To unsubscribe from this group, send an email to: Chrysler300-unsubscribe@xxxxxxxxxxxxxxx <*> Your use of Yahoo Groups is subject to: https://info.yahoo.com/legal/us/yahoo/utos/terms/