Re: [Chrysler300] Replacement for the 413
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Chrysler300] Replacement for the 413





Carl
Do you know of a set of the Short Long Ram exhaust manifolds out there in 300 Land? I have two Ram sets, both the Long Long Ram's as well as the Short Long Ram, not sure just why, but ended with two sets. But was never able to find the header style J/K exhaust manifolds. For that matter a reasonable set of the logs either. I am still looking for the elusive set, that I won't have to sell the car to buy (figurativally speaking). Any help would be appreciated. Thanks in advance.
 
Best Regards,
Stephen A. Noia
1-408-210-4736 cell
From: C Bilter <cbilter@xxxxxxxxx>
To: Anna F Noia <sa-noia@xxxxxxxxxxx>; Dan Akol <dakol@xxxxxxxxx>; Chrysler300@xxxxxxxxxxxxxxx
Sent: Friday, January 31, 2014 11:31 AM
Subject: Re: [Chrysler300] Replacement for the 413
My experience over the last ten years is that the short rams have been more difficult to source and dramatically more expensive than the J/K exhaust headers, although the headers are getting elusive as well.  
 
Carl B with a J (with G long rams ‘cause someone stole its J short rams and put them on a G.  Alphabet soup, fer sure)
 
 
Sent: Friday, January 31, 2014 12:52 PM
Subject: Re: [Chrysler300] Replacement for the 413
 
 
Dan
I have a 440 that I was setting up for a Short Long ram, my hope is that it would run GREAT, sort of like a .120 over 413 would be. Remember more cubes = more horsepower, or so the rumor goes. My problem was I was never able to find a set of the J or K header style exhaust manifolds. Unable to locate a set of J/K exhaust manifolds i put a stock single four barrel with the HP exhaust manifolds. The engine was built for the Ram setup, Cam was similiar to the stock 390 / 400 HP Ram, I am still looking for those elusive manifolds, I hope some one can help. Any way back to your question, the 440 will work replacing the 413. My question is why not make it .080 over with a set of even larger pistons? Make sure your radiator is good (4 core), put in an Engine oil cooler, clutch fan and schroud, to keep it running cool. Just a few suggestions, Good Luck how ever you decide.
 
Best Regards,Stephen A. Noia1-408-210-4736 cell
From: Dan Akol <dakol@xxxxxxxxx>
To: Chrysler300@xxxxxxxxxxxxxxx
Sent: Friday, January 31, 2014 10:00 AM
Subject: [Chrysler300] Replacement for the 413
 
The 413 in my G is .060 over and worn out, so I need a new long block at the least. Question: How does the 440 run with the cross rams? Or should I try to find a 413? Thanks! Dan


__._,_.___


To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to http://autos.groups.yahoo.com/group/Chrysler300/join and select the "Leave Group" button

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang




Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe

__,_._,___


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.