RE: FW: [Chrysler300] regarding C & D mufflers
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: FW: [Chrysler300] regarding C & D mufflers



Hi Keith,
I  checked the measurements of  the two Mufflers, Sono 6X and Sono 4X again
this morning.
The height on yesterdays measurement was off by about  ½ inch, I entered up
the wrong figure from my notes.
 
The height for the Sono 6X at the end seam is 3 7/8? and the Sono 4X is 3
¾?.
Width for the Sono 6X is 8 1/8? to 8 3/16? and the Sono 4X is 8 1/8? to 8 ¼?
measured at the seam and middle.
 
Thanks for checking.
 
John Chesnutt
 
 
From: Keith Boonstra [mailto:kboonstra@xxxxxxxxxxxx] 
Sent: Thursday, January 26, 2012 6:24 AM
To: John L. Chesnutt
Cc: Chrysler300@xxxxxxxxxxxxxxx; 'David Barlow'
Subject: Re: FW: [Chrysler300] regarding C & D mufflers
 
I gave the specs of my Waldron mufflers to Dave privately yesterday, but
I'll put it out here so we can compare.

Here's my note to Dave yesterday:
"OK, here we go, Dave.  I don't know what you call the end crimping
material, but the measurements here include that.  The length is 34.25" and
the end oval is 4.25" X 8.00".  The inlet pipe is 2.25" in the center of the
oval, and the 2" outlet is off center outboard.  I forgot to measure how far
offset from center the outlet is, but I can easily go back and get that
dimension for you if you need it."

I see Waldron's length is nearly the same, and the width fairly close, but
the height is a whole 1" fatter on the Waldron.  Are we sure about the 3.25"
height for a Sono 6X?

Keith Boonstra

-



On 1/26/2012 12:55 AM, John L. Chesnutt wrote: 
  


Hi Dave in UK

I took the measurements today from one of my original type mufflers for our
1957 300C Hardtop. The muffler was purchased from Chrysler in the 1960's. 

The original 300C mufflers were "MoPar Sono 6X" shown in raised relief.
Other Chryslers models in 1957 used "Mopar Sono 4X" which have a body
length of 29 inches.

The "Sono 6X" has a Body length 34 inches, width 8 3/8 inches, height 3 1/4
inches. Inlet pipe 2 1/4 inches and outlet pipe 2 inches.
Length of inlet pipe 2 inches, length outlet pipe 2 3/4 inches.

I would be interested in hearing from Keith Boonstra and Bob Merritt how the
Waldron's mufflers compare to the originals.
Does Waldron's make a 34 inch muffler? Or only the 29 inch (Sono 4X)

In a posting to this Club, 7/23/10, Marv Raguse who has both a 300 C & D,
says he worked with Joe Tonietto of Waldron's and stated that he has the
"Mopar Sono 4X" which was originally thought to be for 300C's. Wayne
Graefen's 1957 Chrysler 300C Handbook originally listed the "MoPar Sono 4X",
but he changed it to the correct "MoPar Sono 6X" as shown in his 6th
Edition.

John Chesnutt, Portland, OR

-----Original Message-----"sono

From: Chrysler300@xxxxxxxxxxxxxxx <mailto:Chrysler300%40yahoogroups.com>
[mailto:Chrysler300@xxxxxxxxxxxxxxx <mailto:Chrysler300%40yahoogroups.com> ]
On
Behalf Of Bob Merritt
Sent: Wednesday, January 25, 2012 11:02 AM
To: Chrysler 300 List
Subject: [Chrysler300] regarding D mufflers

Subject:
Re: [Chrysler300] muffler for a 300D
From:
Keith Boonstra <kboonstra@xxxxxxxxxxxx <mailto:kboonstra%40zeegroup.com> >
Date:
1/25/2012 1:20 PM

To:
black58hemi <barlowdavidt@xxxxxxx <mailto:barlowdavidt%40aol.com> >
CC:
Chrysler300@xxxxxxxxxxxxxxx <mailto:Chrysler300%40yahoogroups.com> 

Hi Dave,

Waldron's Exhaust here in Michigan has put considerable effort into 
making a very correct muffler in stainless steel for the C and D (and 
perhaps others), and they're a very good company to work with. I have a 
set of theirs on my C, and couldn't be more pleased.

Perhaps the shipping cost to the UK would be prohibitive, and thus you 
need to have them manufactured there. If so, one of us here in the 
States can give you the dimensions you're looking for. What's the 
word? Waldron's or the specs?

Keith Boonstra
Holland, Michigan

-

On 1/25/2012 12:47 PM, black58hemi wrote:

Hi everyone.
Could anyone let Me know the correct dimensions for the mufflers on a 
300D hardtop. I need the length, width and depth of the muffler and also 
the internal diameter of the inlet pipe.
I have found a shop local to Me to make the system in stainless and they 
have already done the front and tail pipes from pattern but when I got 
the car the mufflers had rusted away long ago.
Thanks Dave.
300D in the UK.

[Non-text portions of this message have been removed]

------------------------------------



[Non-text portions of this message have been removed]



------------------------------------

To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to http://autos.groups.yahoo.com/group/Chrysler300/join and select the "Leave Group" button

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylangYahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    Chrysler300-digest@xxxxxxxxxxxxxxx 
    Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/



Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.