Re: [Chrysler300] 300 G Heater Control

[Ray Jones <hurst300@xxxx>]

You can repair the plastic nipples with small metal tubes. Determine the
I.D. of the nipples and find some tubing with the same size O.D. Possable
choice is Ball Piont Pen ink cartriges. Nice strong tube and just might be
right. Work the tube into the valve and work the nipple on the tube. Use an
epoxy glue as lubricant, and you won't see the fix, Nor have it break again.
See ya in Dayton, Ray Jones

> From: "Antonello Jelitro" <mopar@xxxx>
> Date: Wed, 2 Jul 2003 20:25:05 +0200
> To: <Chrysler300@xxxxxxxxxxxxxxx>
> Subject: Fw: [Chrysler300] 300 G Heater Control
> 
> 
> 
> 
> 
>> Hello from Italy
>> I got my rebuilt one for my G from Jeff Carter. His address is on the link
>> page of our website. He rebuilt mine, rechromed the bezel and painted the
>> small arrows. Very nice job
>> Antonello Jelitro
>> ----- Original Message -----
>> From: "Lauren R Lampi" <lrlampi@xxxx>
>> To: <Chrysler300@xxxxxxxxxxxxxxx>
>> Sent: Wednesday, July 02, 2003 8:09 PM
>> Subject: [Chrysler300] 300 G Heater Control
>> 
>> 
>>> Hi 300 Group,
>>> 
>>> Need some help with the heater control block for a 300G ,Non Air.
>>> This is the Plastic, 5 button control block, for the vaccuum lines
>>> and electric connectors.
>>> 
>>> Part number 2096083
>>> For five push buttons from the front
>>> and 7 vaccuum hose connectors on the back.
>>> 
>>> It is about 3 7/8" wide, 1 1/4' deep, 1' high.
>>> 
>>> Three of the vaccuum connectors on the back of the block
>>> have broken off. Old age and stress????
>>> I have the broken off pieces.
>>> 
>>> Are there NOS, good used, Repro ones out there???
>>> Or can I repair the one that I have???
>>> 
>>> Can you "glue, epoxy, cement" the little vaccuum connectors
>>> back on and will it work well enough??
>>> 
>>> I think there was some discussion about this part and repair
>>> one or two years ago.
>>> 
>>> Any help would be appreciated.
>>> 
>>> 300ly
>>> Lauren R Lampi
>>> 300G under construction
>>> (Yes, This is the one that was rear-ended by a boat while it
>>> was locked in my garage)
>>> Grand Rapids, Minnesota
>>> 
>>> 
>>> 
>>> To send a message to this group, send an email to:
>>> Chrysler300@xxxxxxxxxxxxxxx
>>> 
>>> For list server instructions, go to
>> http://www.chrysler300club.com/yahoolist/inst.htm
>>> 
>>> To unsubscribe from this group, send an email to:
>>> Chrysler300-unsubscribe@xxxxxxxxxxxxxxx
>>> 
>>> 
>>> 
>>> Your use of Yahoo! Groups is subject to
> http://docs.yahoo.com/info/terms/
>>> 
>>> 
>>> 
>> 
>> 
> 
> 
> 
> 
> To send a message to this group, send an email to:
> Chrysler300@xxxxxxxxxxxxxxx
> 
> For list server instructions, go to
> http://www.chrysler300club.com/yahoolist/inst.htm
> 
> To unsubscribe from this group, send an email to:
> Chrysler300-unsubscribe@xxxxxxxxxxxxxxx
> 
> 
> 
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
> 
> 
>