Re: {Chrysler 300} 300F Backfire thoughts?
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: {Chrysler 300} 300F Backfire thoughts?



error , should be 0.27  uF slipping !  ( yow) 
Driving  the tune up back then was usually rubbing block wears down a bit changing gap generally closing the points up .
Soon misfires , as no longer the clean break/ big spark  at .018 or so . A compromise , more than about .018 brings bounce , arcing at bounce , less dwell .Will break down  at high rpm not enough dwell . Why dual points on high perf engines ( Petty  did ok with dual points at Nascar /  hemi )  Closer than correct by quite a bit will bring on an arc across the gap as they open , don’t open enough , 
weak erratic spark , missing etc 
but seems that takes 15000 miles ? We are not driving these cars 15000 (?,,except Noel !) so annual check with dwell meter is reasonable . 
Note with  dwell meter , the old kind , you do not even  open the distributor . 
literally 45 seconds .
45 hours trying to diagnose erratic pertrinix bs  ??? , then  change it , still gives same  problem . been there 

On Aug 2, 2024, at 9:47 AM, Tom Wilburn <tomwilburn1@xxxxxxxxx> wrote:

First I have heard of “lifetime” points. 

Was it the condensor driving the standard “points and condenser” annual tuneup in the day?

Tom
Sent from my iPhone

On Aug 2, 2024, at 8:13 AM, John Grady <jkg@xxxxxxxxxxxxxxxxx> wrote:


To further add some fuel , why change points ever ? cause they don't look pretty ? Or it’s a nice day for a tune up ? 
As long as dwell is right, by dwell meter,  appearance does not  matter electrically  ; metal  to metal is a perfect electrical connection and oxides etc will burn off .They form on your brand new ones in a few miles 
just reset gap 4-5 x only with dwell meter , they will live as long as engine  
And to James point if not square bend them till they are .
Changing them for nothing is half the problem we cause ourselves . 

On capacitor , I now use .027 1200 V panasonic radio caps  , Japanese’s quality control is bulletproof can be mounted outside the cap gain some  room , use radio two or three terminal solder strip .
But if you find  old mopar with copper strap grab them . 6 or 12 v same cap will work . 

On Aug 2, 2024, at 12:00 AM, 'Ron Waters' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx> wrote:



From what I’ve heard, people are dissatisfied with current production of points and condensers. That’s why many folks search for good quality old stock of these items. Ebay is a good source.

 

Ron

 

From: James Douglas
Sent: Thursday, August 01, 2024 4:50 PM
To: Ron Waters <ronbo97@xxxxxxxxxxx>; chrysler-300-club-international@xxxxxxxxxxxxxxxx
Subject: RE: Re[2]: {Chrysler 300} 300F Backfire thoughts?

 

Well,

 

Since SMP moved the production line from Long Island City to Mexico the quality of the points has been crap. I ordered a dozen sets for my Desoto’s a few years back and they had holes that were off and the plating on the bottom was so bad the bottom of the plate would not sit flat. I sent them back waited six months and order a couple and they were the same.

 

So, although a lot of people still know how to set points, the quality of them is getting so poor it does not matter how good you are.

 

That is one reason people look for alternatives.

 

The other issue is the crap condensers.

 

James

 

From: 'Ron Waters' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Sent: Thursday, August 1, 2024 1:38 PM
To: chrysler-300-club-international@xxxxxxxxxxxxxxxx
Subject: RE: Re[2]: {Chrysler 300} 300F Backfire thoughts?

 

And the funny thing is, a Pertronix is totally unnecessary for the successful operation of our cars. No idea why anyone feels they need to install one of these. Laziness ? Ignorance, based on unwillingness to learn how to set points ? Some Internet Influencer with three million followers told them to do so ? SMH.

 

Ron

 

From: chrysler-300-club-international@xxxxxxxxxxxxxxxx On Behalf Of dplotkin@xxxxxxxxxxxxxxxxxxx
Sent: Thursday, August 01, 2024 3:48 PM
To: Carl Bilter <cbilter@xxxxxxxxx>
Cc: Andy Mikonis <r41hp@xxxxxxxxx>; John Lazenby <french_fryguy@xxxxxxxxx>; Lindsey Fuller <lindsey@xxxxxxxxxxxxxxx>; John Grady <jkg@xxxxxxxxxxxxxxxxx>; 'Bob Meritt <bob@xxxxxxxxxxxxx>; Jean-Yves Chouinard <jymopar@xxxxxxxxxxx>; Jim Marino <jpm0855@xxxxxxxxx>; chrysler-300-club-international@xxxxxxxxxxxxxxxx
Subject: RE: Re[2]: {Chrysler 300} 300F Backfire thoughts?

 

Carl-

I have no idea how much experience you have across many cars with Pertronix. However I lurk on a variety of different old car forums in which the like minded share experience as we do here. I don't condemn a product in wide use lightly. 

 

The failures of Pertronix are widely known in the old car hobby, especially among the Corvette community which is far larger than our letter car community, with many more cars and people. The evidence I have seen there over 12 years is far from anecdotal. 

 

Is some of it failure to follow instructions? Yes. Do many use Pertronix without a problem. Must be. Have a great many been relegated to the side of the road because of a properly installed but defective product? Absolutely. 

 

I agree with you Carl that the problem could be elsewhere. However given what the greater hobby has experienced with Pertronix, the first thing someone with Pertronix and an ignition related running problem should do is rule out the Pertronix first! Screw in a set of points and see what happens. 

 

This does not have to be an argument. It's a discussion where everyone can learn from each other. 

 

Danny Plotkin

 

-----Original Message-----
From: "Carl Bilter" <cbilter@xxxxxxxxx>
Sent: Thursday, August 1, 2024 3:14pm
To: "Andy Mikonis" <r41hp@xxxxxxxxx>, "John Lazenby" <french_fryguy@xxxxxxxxx>
Cc: dplotkin@xxxxxxxxxxxxxxxxxxx, "Lindsey Fuller" <lindsey@xxxxxxxxxxxxxxx>, "John Grady" <jkg@xxxxxxxxxxxxxxxxx>, "'Bob Meritt" <bob@xxxxxxxxxxxxx>, "Jean-Yves Chouinard" <jymopar@xxxxxxxxxxx>, "Jim Marino" <jpm0855@xxxxxxxxx>, "chrysler-300-club-international@xxxxxxxxxxxxxxxx" <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: Re[2]: {Chrysler 300} 300F Backfire thoughts?

I did not intend to reignite the Pertronix debate with my post.  Lindsey asked if the Pertronix might factor into his problems.  Of course it is possible, but my point was that I basically disagreed with Danny that it "increases the odds greatly."  I would start by looking at other issues first.  That is hardly blaming something else.  It is trying to help a fellow member get timely resolution to a problem.   I also never said it can't cause a backfire.  It most definitely is possible.  I just suspect that is an exception, very atypical (in a correct installation, on a Prestolite dual point, no clue on a Camaro)).  We all have different opinions and that heps all of us when there is a problem.  

We don't know that failure rate of the Pertronix units in the field and to what degree the root cause is due to "user error."  Anecdotal evidence is insufficient to draw proper conclusions.  I appreciated John Lazenby's post beause he has more direct experience with the product and the vendor than most (or all) of us.  John could not have run a successful parts business for 40-50 years selling products that don't work.  

To address Andy's question, the product has weak points and user installation (or operational) errrors can contribute greatly to its premature demise.  In fact, I did an entire video on the subject, specifally in reference to use in the Prestolite dual point distributors.  See here:  Pertronix Ignitor (youtube.com)  If you don't have 13 minutes to watch the video, I'll summarize:

1.  Bad ground.  Needs to be not greater than 0.2 ohms.  (ground is also critical with Mopar ECU box).  User installation error. 

2.  Low voltage, esp. running unit in series with ballast resistor, as Danny mentions, by connecting the red wire to coil pos. instead of a full 12V source.  It will work - but could shorten life and cause other problems.  User installation error. 

3.  Wrong air gap.  Usually doesn't work at all.  User needs to check.  User installtion error.

4. Magnet sleeve not fully seated.  User installtion error. 

5. Installing unit in a worn distributor.  All sorts of issues can occur.  User insatllation and operation error.  

6.  Operation with faulty alternator, generator, voltage regulator, or weak battery.  Low or high voltage damages unit over time.  Voltage spikes are possible.   User operational error.  

7.  Failure to readjust ignition timing after installation.  User insatllation error.  

Other issues not associated with user installation error:

1.  Heat.   Can damage unit over time.  

2.  Unit uses the breaker plate as a heat sink.  May not really be adequate.  Not any choice as unit must fit under the distributor cap.  

I am not saying that the Pertronix is a better solution than factory breaker points.  It is an alternative solution.  The module is a solid state switching device  (probably a Darlington switch in EE terms, but not sure).  It provides a consistent spark over time (when operating as designed).  The spark is cleaner.  But not stronger. - due to voltage drop on switch.  John Grady 100% correct on that, as always.  

Carl B. 

------ Original Message ------

From "'Andy Mikonis' via Chrysler 300 Club International" <chrysler-300-club-international@xxxxxxxxxxxxxxxx>

To "John Lazenby" <french_fryguy@xxxxxxxxx>

Date 7/31/2024 11:58:20 PM

Subject Re: {Chrysler 300} 300F Backfire thoughts?

What kind of user installation error makes a pertronix fail later “on the road”? Maybe it’s a user issue if there is a “no start” on the initial install. If you want to blame “something else” then why is pertronix better than staying with points and checking them once in a while?

To paraphrase my favorite east coast EE, no one knows ignition like the automobile manufacturers, and they figured it out over a century ago; the aftermarket has nothing on them. Also, if you understand your points system, you can fix it on the side of the road. If your aftermarket ignition fails you walk

 

On Jul 31, 2024, at 9:03 PM, 'John Lazenby' via Chrysler 300 Club International <chrysler-300-club-international@xxxxxxxxxxxxxxxx> wrote:

Well, I figured I jump in here and make a few comments.  First, I'm not an "electronics guy" other than I know not to put my finger in the wall socket.

For years my company, Royze Inc. sold the Pertronix line.  I became friends with John G. a fellow VW guy who was the national sales manager at Pertronix and between the two of us we got the unit for the early Hemi Dual Point Distributors put into product.  The original prototype is in my parts bin as I write this.

From time to time we would get units back from customers stating they were faulty.  If they were in the warranty period we would replace the unit no questions asked.  Those "faulty" units would be sent back to Pertronix for inspection and we would be issued credit.  John ALWAYS sent me a report on any units that went back and virtually none of them were bad.  I'm not saying it never happened but it was seldom.

On a personal not I've run these units in our 300B and 300C for over 25 years without issues.  Now to be as objective as I can I did try one in our '55 NYer T&C and had issues of it firing.  According to John the 6 volt units were marginal at best.  So on that car I went back to dual points and no further issues.  I sold the business and retired over six years ago and John G. also retired from Pertronix shortly thereafter.

John Lazenby

On Wednesday, July 31, 2024 at 06:47:55 PM PDT, Carl Bilter <cbilter@xxxxxxxxx> wrote:

An eight year old Pertronix Ignitor module would not be of the older variety.  The trouble prone modules were those from 25 or more years ago, and most problems were "user installation error."

And a Pertronix means no points, no capacitor.  They tend to be all or nothing which equates to failure meaning no spark. 

I think fuel/carb issue unless timing is off.  

Carl B.  

------ Original Message ------

To "Lindsey Fuller" <Lindsey@xxxxxxxxxxxxxxx>

Cc "John Grady" <jkg@xxxxxxxxxxxxxxxxx>; "Carl Bilter" <cbilter@xxxxxxxxx>; "'Bob Meritt" <bob@xxxxxxxxxxxxx>; "Jean-Yves Chouinard" <jymopar@xxxxxxxxxxx>; "Jim Marino" <jpm0855@xxxxxxxxx>; "chrysler 300 club" <chrysler-300-club-international@xxxxxxxxxxxxxxxx>

Date 7/31/2024 3:31:28 PM

Subject Re: {Chrysler 300} 300F Backfire thoughts?

Use of Pertronix increases the odds greatly that the trouble lay with ignition and likely the Pertronix module itself. The older variety are known to eventually fail and backfiring is among the presentations. 

 

Danny Plotkin

-----Original Message-----
From: "Lindsey Fuller" <Lindsey@xxxxxxxxxxxxxxx>
Sent: Wednesday, July 31, 2024 3:47pm
To: "John Grady" <jkg@xxxxxxxxxxxxxxxxx>
Cc: "Dan Plotkin" <dplotkin@xxxxxxxxxxxxxxxxxxx>, "Carl Bilter" <cbilter@xxxxxxxxx>, "'Bob Meritt" <bob@xxxxxxxxxxxxx>, "Jean-Yves Chouinard" <jymopar@xxxxxxxxxxx>, "Jim Marino" <jpm0855@xxxxxxxxx>, "chrysler 300 club" <chrysler-300-club-international@xxxxxxxxxxxxxxxx>
Subject: Re: {Chrysler 300} 300F Backfire thoughts?

Thanks for all the input. I should have mentioned that I switched to Pertronics ignition during restoration 8 years ago. Not sure if that changes any of your ideas.

 

On Mon, Jul 29, 2024 at 8:10 AM John Grady <jkg@xxxxxxxxxxxxxxxxx> wrote:


very good point Dan , i jumped to tail pipe backfire , more likely a carb backfire , accell pump check valve sticks on these , no squirt ? one side . Especially off idle 

Same issues apply . Haven’t be careful myself , which kind of backfire 

I had quite a dance last week with one of my cars , will be long story , Later on . I write long stories . This one is real . 

but end point : NEVER hold wire in hand to check spark or run with a coil wire off distributor or pulled plug wire etc . Unloaded plug volts  can exceed 60000 will break down the coil inside , especially old one . voltage is clamped to 20000 or under , by the outside plug gap .Make tester  of old plug and ground wire 

All this last week led to discovering a 10$ tester on amazon with adjustable screw  gap , set it to 20 kv , to test spark . Great tool . Never knew about it . Fits on wire . Critical in fact to check spark without hurting the coil inside . It will hold the bolts down like a plug 

Once you hurt your coil you  get occasional poor running , or one day won’t start right , on and on and sends you down a very long  garden path maybe for years .And intermittent as all get out .  Reason : Part of spark is sometimes reduced by coil carbon track inside the coil . Sometimes … 

I have done that we all have . It DOES damage coil . 

We keep

learning 

John 

Begin forwarded message:

From: John Grady <jkg@xxxxxxxxxxxxxxxxx>
Date: July 29, 2024 at 8:03:08 AM EDT
To: Lindsey <lindsey@xxxxxxxxxxxxxxx>
Subject: Re: {Chrysler 300} 300F Backfire thoughts?

hi backfire is not usually a plug issue or wire at plug either . A failure there usually means obvious skip ,( it is then  not firing, as  opposed to firing ant wrong time)  and although that skip could lead to fuel vapor in exhaust etc , i have never seen that . And it would skip . If skip , dirty plug a hard run might help , like uphill .

but my money is on incorrect points setting too tight . you really can’t do it right with out an old fashioned dwell meter as they are critical and tend to change as you tighten the screw . See ebay old sears dwell meter

Also the capacitor . If someone replaced yours with one with rubber conical nose they are junk . Hard to find but original mopar has a copper strap out of cap
I may not  be right on all this , from afar but what I would do …
hope it helps
j

On Jul 28, 2024, at 10:24 PM, Lindsey <lindsey@xxxxxxxxxxxxxxx> wrote:

Have hardly driven my F this year due to wet and nasty weather and waiting to get my brakes fixed properly. Finally took it for an hour or so city cruise last Sunday. After a slow crawl through a show and shine, i stopped at a red light. Accelerated medium throttle and heard a backfire, probably mine. 5 minutes later hit another red light and motor was shaking at idle. Obviously a cylinder not happy. Got home ok. Not able to bend down at moment to pull front wheels and access covers to get at plugs. No signs of arching on coil or distributor cap contacts that i could see. Cap for #1 cylinder had a bit of loose black stuff at bottom which cleaned up with a q tip. Took it out again and seemed fine, motor smooth, good moderate acceleration, no highway. Came to a stop sign on a remote road. Didn’t come to a full stop, then began accelerating modestly and a small backfire. The car has always run a bit rich since restoration i believe. Any thoughts before I get it to my out of town mechanic?

Thanks.

Lindsey in fires fire free Winnipeg

Sent from my iPad

--

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang

---

You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.

To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.

To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/5E4AA8F6-2088-4846-925C-7114CA164F64%40fullerfamily.ca.

 

 

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit

https://groups.google.com/d/msgid/chrysler-300-club-international/em935bbb52-26f2-4fbd-ba48-7affe10b5ae9%4040a70714.com

.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/772171976.2397962.1722477835484%40mail.yahoo.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/3E6E5E7B-0E02-4B32-97B1-D306C0D532B2%40yahoo.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/em3106c873-9887-4416-9db7-ab04255f2604%4020d0f2ac.com.

 

 

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/1722541689.976329812%40apps.rackspace.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/003f01dae452%24a4a5c730%24edf15590%24%40comcast.net.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/000d01dae488%241d909230%2458b1b690%24%40comcast.net.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/E9A7C79D-4053-4B17-A765-F2CE32DC73F9%40gradyresearch.com.

--
For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
---
You received this message because you are subscribed to the Google Groups "Chrysler 300 Club International" group.
To unsubscribe from this group and stop receiving emails from it, send an email to chrysler-300-club-international+unsubscribe@xxxxxxxxxxxxxxxx.
To view this discussion on the web visit https://groups.google.com/d/msgid/chrysler-300-club-international/3C82C470-60A9-47F5-9E27-C8DFB369F34C%40gradyresearch.com.


Home Back to the Home of the Forward Look Network Archive Sitemap


Copyright © The Forward Look Network. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
This site contains affiliate links for which we may be compensated.