RE: [Chrysler300] Smooth as Silk drive shaft : )

["'David Schwandt' finsruskw@xxxxxxxxxxxxxxx [Chrysler300]" <Chrysler300-noreply@xxxxxxxxxxxxxxx>]

OK!

Whatever.

I’m still vibration free after all these years.

Earlier 50’s cars had ‘em on both ends even.

I beat my 56 Dodge to death and don’t recall any d/train problems.

I wonder what Mr. K did to his 3-300’and B’s

 

From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On Behalf Of John Kuegel jwkco@xxxxxxxxx [Chrysler300]
Sent: Saturday, April 09, 2016 8:25 AM
To: David Schwandt; 'David Schwandt' finsruskw@xxxxxxxxxxxxxxx [Chrysler300]; 'John Grady'; 'William Leahy'
Cc: 'Rob Kern'; Chrysler300@xxxxxxxxxxxxxxx
Subject: RE: [Chrysler300] Smooth as Silk drive shaft : )

 



I did this to my F about 6 years ago and it is a a nice performance/lower maintenance/ reliability improvement...it cost more than your job recently, as I sourced a donor shaft from a '60 NY'er. I didn't want to cut up my original stock shaft...as I recall, the donor shaft was a little hard to find because there were 2 different diameter drive shafts on the cars depending on the model. It was the larger diameter one that I used and was almost identical in appearance to mine from the F. The shop that did it is in Georgia near Atlanta, I think it was...I can find out for anyone who is interested. This shop has done many of these conversions for lots of Forward Look folks. I got the contact info from the Plymouth Club bulletin as I recall. All I needed to provide the shop with was the length in inches of my original shaft, the year and model of my car, and then send them the donor shaft. I keep my original shaft in the packaging that they sent the converted one back to me and it's in the trunk! (and it's ready to go as a spare if I ever need it)

John Kuegel

 

Sent from Yahoo Mail on Android <https://overview.mail.yahoo.com/mobile/?.src=Android> 

 

On Sat, Apr 9, 2016 at 8:15 AM, 'David Schwandt' finsruskw@xxxxxxxxxxxxxxx [Chrysler300]

<Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:

  

I would not say poor design. Outdated maybe, but not poor.

After all, it was around for many millions of miles.

Just needed regular maintenance, like everything else mechanical.

From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On Behalf Of John Grady jkg@xxxxxxxxxxxxxxxxx [Chrysler300]
Sent: Saturday, April 09, 2016 6:34 AM
To: William Leahy
Cc: Rob Kern; <Chrysler300@xxxxxxxxxxxxxxx>
Subject: Re: [Chrysler300] Smooth as Silk drive shaft : )

I have done this .. Way to go .the old one is a very poor design . Good only for flat six . That is a great price . Maybe make some deal w club --send our shafts there . Even with 100$ ship if they are good and do it well it is a great deal . Too many duffers will ruin shaft . You need to be skilled to do perfectly , have right equipment . Nice find Rob .

The flanged Fitting for a modern joint is used on Winnebago motor homes , not an uncommon part . 

Sent from my iPhone

On Apr 9, 2016, at 12:14 AM, William Leahy bleahy@xxxxxxxxxxx [Chrysler300] <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:

I need to address this / thankx, Bill Leahy in summer like Kennewick, Washington 

Sent from my iPad

On Apr 8, 2016, at 7:47 PM, "'Rob Kern' robkern@xxxxxxxxxxxxx [Chrysler300]" <Chrysler300-noreply@xxxxxxxxxxxxxxx> wrote:

Hello 300’ly to all!

I just replaced the front ball and trunion u-joint assembly on my C with the upgrade of the slip assembly more modern front u-joint and I must say that I could not be more pleased. The car runs as smooth as silk and is quieter. It almost feels like the vehicle is at peace with itself! I had tremors develop between 30 and 40 mph upon easy acceleration and again when accelerating above 60mph. The front U-joint had 1/16th inch play. The grease retention boot was replaced a month ago when discovered that it left the party who knows how long ago. The new u-joint was installed to the front of the driveshaft which was balanced with the rear u-joint in place and then installed. Precision Drive Shaft in Oklahoma City did all the work and obtained all the parts . 3 day turn around time. $298.00. Many thanks to Club members Mike Burke, George McKovich, Larry Jett, Murray Park and Jeff Carter for discussing the upgrade and helping me decide to go this route! Rob Kern

[Non-text portions of this message have been removed]










[Non-text portions of this message have been removed]



------------------------------------
Posted by: "David Schwandt" <finsruskw@xxxxxxxxxxxxxxx>
------------------------------------

To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx

To unsubscribe from this group, send an email to bob@xxxxxxxxxxxxx or
go to https://groups.yahoo.com/neo/groups/all/manage/edit

For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/search.htm#querylang
------------------------------------

Yahoo Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    Chrysler300-digest@xxxxxxxxxxxxxxx 
    Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo Groups is subject to:
    https://info.yahoo.com/legal/us/yahoo/utos/terms/