RE: [Chrysler300] '55 Chrysler 300 radiator house source?

["Richard Barber" <c300@xxxxxxx>]

John:

 

Thanks for a clear and prompt response.  I’ll check those out tomorrow.  One never knows when one will need a spare.

 

Rich Barber

Brentwood, CA

 

From: Chrysler300@xxxxxxxxxxxxxxx [mailto:Chrysler300@xxxxxxxxxxxxxxx] On Behalf Of cotejohnr@xxxxxxx
Sent: Wednesday, August 11, 2010 6:59 PM
To: cotejohnr@xxxxxxx; c300@xxxxxxx; lhh225@xxxxxxx
Cc: Chrysler300@xxxxxxxxxxxxxxx; john@xxxxxxxxx; pharmissy@xxxxxxx
Subject: Re: [Chrysler300] '55 Chrysler 300 radiator house source?

 

  


Not to be misleading, but as I recall, the NAPA #7711may need only a slight trim in length on radiator end as well but contours are great after that.
John

-----Original Message-----
From: cotejohnr@xxxxxxx <mailto:cotejohnr%40aol.com> 
To: c300@xxxxxxx <mailto:c300%40ez2.net> ; lhh225@xxxxxxx <mailto:lhh225%40aol.com> 
Cc: Chrysler300@xxxxxxxxxxxxxxx <mailto:Chrysler300%40yahoogroups.com> ; john@xxxxxxxxx <mailto:john%40royze.com> ; pharmissy@xxxxxxx <mailto:pharmissy%40cox.net> 
Sent: Wed, Aug 11, 2010 9:51 pm
Subject: Re: [Chrysler300] '55 Chrysler 300 radiator house source?

Hi all,

Molded hose for '56 upper......... NAPA # 7711 molded and fits like a glove.
Molded hose for lower..........Carquest # 20046 molded and may need only slight trim on length (actually is listed as fitting a lower on '57 Windsor!)

John Cote
Too many '56's

-----Original Message-----
From: Richard Barber <c300@xxxxxxx <mailto:c300%40ez2.net> >
To: 'LHH225' <lhh225@xxxxxxx <mailto:lhh225%40aol.com> >
Cc: Chrysler300@xxxxxxxxxxxxxxx <mailto:Chrysler300%40yahoogroups.com> ; John Lazenby <john@xxxxxxxxx <mailto:john%40royze.com> >; Bob Linnenberger <pharmissy@xxxxxxx <mailto:pharmissy%40cox.net> >
Sent: Wed, Aug 11, 2010 8:02 pm
Subject: [Chrysler300] '55 Chrysler 300 radiator house source?

Leonard Hodgdon:

My non a/c C-300 has a molded hose, but no ID on it. The water outlet/thermostat housing has a vertical outlet, the hose starts vertically, then has a couple of bends to the offset horizontal radiator connection. The edge of the oil filler vent cap just touches the hose.

I just took my C-300 down to NAPA and found they did not have a molded hose for ’55-’56, but did have one for ‘57’s with or without a/c. They did have a molded hose #9067 that looked like it might fit after being cut in half. The ID may not fit over the block outlet. Cost about $20.

I then visited Kragen who said they had one in stock. It wasn’t a molded hose.

The Gates site referenced on our website only has flex hose for 1955 Chrysler 300’s. However, it looks to be a valuable site. See: http://www.gates.com/part_locator/index.cfm?location_id=3002 The Goodyear parts catalog has only a flex hose. Ditto, Dayco which says inlet and outlet are 1.75”. If none of these major manufacturers is making/stocking/selling the molded hoses, good used and NOS may be quite valuable.

Parts book numbers indicate there were a wide range of hoses:
Top hose “inlet”: 55-56 w/o a/c: 1615493, w/a/c: 1637669
Lower hose “outlet”: ’55-’56 Windsor: 1616229; NY, Imp, 300: 1558435; ’56 w/a/c: 1670490.
The water outlet part number for all ’55-’56 Chryslers is the same for all models 1536376.

Andy Bernbaum shows a molded hose (J-221) in his parts catalog, but it is too late in the day to confirm availability and price. See: http://www.oldmoparts.com/j.htm 

Let’s go to the consultants and server to see if anyone has a source for the ’55 or ’56 upper and lower molded radiator hoses.

C-300’ly,
Rich Barber
Brentwood, CA

From: LHH225 [mailto:lhh225@xxxxxxx <mailto:lhh225%40aol.com> ] 
Sent: Wednesday, August 11, 2010 12:08 PM
To: richard barber
Subject: top hose

Rich Anyone you know that has found or matched up a molded upper hose for a C300 w ac or not!

[Non-text portions of this message have been removed]

[Non-text portions of this message have been removed]





[Non-text portions of this message have been removed]



------------------------------------

To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx


To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx


For list server instructions, go to http://www.chrysler300club.com/yahoolist/inst.htm

For archives go to http://www.forwardlook.net/300-archive/Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Chrysler300/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/Chrysler300/join
    (Yahoo! ID required)

<*> To change settings via email:
    Chrysler300-digest@xxxxxxxxxxxxxxx 
    Chrysler300-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    Chrysler300-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/