------------------------ Yahoo! Groups Sponsor ---------------------~-->
Yahoo! Autos. Everything you need to know about buying or selling a car.
FREE Quotes, 360° Tours, Research,
Blue Book, Compare Vehicles, Buy Used
http://us.click.yahoo.com/kEZsdA/bwnGAA/YiGOAA/8LmulB/TM
---------------------------------------------------------------------~->
To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx
For list server instructions, go to
http://www.chrysler300club.com/yahoolist/inst.htm
To unsubscribe from this group, send an email to:
Chrysler300-unsubscribe@xxxxxxxxxxxxxxx
------------------------------------------------------------------------
There are 5 messages in this issue.
Topics in this digest:
1. RE: Seat Belts & "Boots"
From: Doug Warrener <dwarrener@xxxxxxxxxxxx>
2. Internet address
From: vhelbling@xxxxxxx
3. 62-63 Seat Belt "Boots"
From: "Mike Zagata" <mzagata@xxxxxxxxxxx>
4. 300 models
From: "Wayne Wunderlich" <texan@xxxxxxxxx>
5. 60 F grille PIeces Needed
From: "Henry Hopkins" <hhrp@xxxxxxxxxxxxx>
________________________________________________________________________
________________________________________________________________________
Message: 1
Date: Thu, 20 Nov 2003 09:17:36 -0800
From: Doug Warrener <dwarrener@xxxxxxxxxxxx>
Subject: RE: Seat Belts & "Boots"
Mike, I did not include the material folded back on itself. I extended the
belt to it's maximum length and measured end to end. I can measure the
length that is folded back for the stitching if you need that info. Doug
W.
-----Original Message-----
From: Mike Zagata [mailto:mzagata@xxxxxxxxxxx]
Sent: Tuesday, November 18, 2003 4:21 PM
To: Doug Warrener
Subject: Re: [Chrysler300] Seat Belts & "Boots"
Doug, did your measurement include the material folded back on itself and
stitched at both ends of each belt? Exactly how did you measure each
side?
Mike PS: The WESCO folks are great. Thanks for the tip.
----- Original Message -----
From: "Doug Warrener" <DWarrener@xxxxxxxxxxxx>
To: "'Mike Zagata'" <mzagata@xxxxxxxxxxx>
Cc: <Chrysler300@xxxxxxxxxxxxxxx>
Sent: Tuesday, November 11, 2003 12:54 PM
Subject: RE: [Chrysler300] Seat Belts & "Boots"
Mike and Guy,I purchased sealt belts for my 300H from WESCO PERFORMANCE;
215
Ramona Pl.; Camarillo,Ca 93010. E-mail " wesco performance.com ", Phone:
805-738-0223. Cost was $24.00 per set, and the item no. is LL74-02, I
think.
I measured my old "H" belts last night. The belting measurement on the
buckle piece is 45", and on the insert piece is 22-1/2". Hope this helps.
You might also try Snnake-Oyl as someone else suggested. They will restore
my old original belts for about $180 for both sets.
-----Original Message-----
From: Mike Zagata [mailto:mzagata@xxxxxxxxxxx]
Sent: Monday, November 10, 2003 1:07 PM
To: Doug Warrener
Subject: Re: [Chrysler300] Seat Belts & "Boots"
Doug, I am interested. Thank you for getting back with me. Mike
----- Original Message -----
From: "Doug Warrener" <DWarrener@xxxxxxxxxxxx>
To: "'Mike Zagata'" <mzagata@xxxxxxxxxxx>
Cc: <Chrysler300@xxxxxxxxxxxxxxx>
Sent: Monday, November 10, 2003 11:45 AM
Subject: RE: [Chrysler300] Seat Belts & "Boots"
Hi Mike, I know where you can purchase new after market belts with the "J"
hooks. I have a set in my 300H. They are almost equal to originals. I have
no idea where you can find the anchor assemblies. If you are interested,
let
me know and I will look up the source tonight. Doug Warrener
-----Original Message-----
From: Mike Zagata [mailto:mzagata@xxxxxxxxxxx]
Sent: Monday, November 10, 2003 7:08 AM
To: Chrysler300@xxxxxxxxxxxxxxx
Subject: [Chrysler300] Seat Belts & "Boots"
Hello fellow club members. I'm new to the club, but not to Chrysler. I
was
lucky enough to be sponsored by Mopar while racing max wedges in the 60s.
I am in need of 2 "sets" of seat belts for the 62 or 63 Chrysler
bucket-seat
cars (Chrysler 300, Plymouth Sport fury, Dodge Polara 500) (1 set = male
insert with belt and anchor end and female buckle with belt and anchor
end).
The belt material has a fine 4-weave pattern (as opposed to being
uniformly
course) and can be black or tan. Each anchor end consists of 2 flat
pieces
of metal with a "J" hook on one end and a rectangular slot for the belt in
the other end. The two flat pieces are held together by a small machine
screw and lock nut. I need 8 of the flat plates with "J" hooks.
The "J" hooks pass through an "eye" bolt which passes through a large,
flat
washer, then through a hole in the floor, where it screws into a plate
with
a nut welded onto it. I need 4 eye bolts, 4 large washers, and four plates
with nuts.
Last, but certainly not least, I need the black vinyl "boots" or sleeves
that cover the 2 plates and anchor bolt for each belt segment. Each boot
is
about 7 inches long, flat for most of its length and then flares out to
form
a round base with 2 "ears" for the metal plates. I need 4 of these - 1
for
each belt segment.
[Non-text portions of this message have been removed]
To send a message to this group, send an email to:
Chrysler300@xxxxxxxxxxxxxxx
For list server instructions, go to
http://www.chrysler300club.com/yahoolist/inst.htm
To unsubscribe from this group, send an email to:
Chrysler300-unsubscribe@xxxxxxxxxxxxxxx
Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
________________________________________________________________________
________________________________________________________________________
Message: 2
Date: Thu, 20 Nov 2003 17:16:26 EST
From: vhelbling@xxxxxxx
Subject: Internet address
Please change my internet address to vhelbling@xxxxxxxxxxxxxxx thanks
V. Helbling
[Non-text portions of this message have been removed]
________________________________________________________________________
________________________________________________________________________
Message: 3
Date: Thu, 20 Nov 2003 19:32:44 -0500
From: "Mike Zagata" <mzagata@xxxxxxxxxxx>
Subject: 62-63 Seat Belt "Boots"
Hello again. Still looking for the black vinyl "boots" or sleeves that
slide over the seat belting material and cover the hardware where the
belts are anchored to the floor. These boots were used on the bucket seat
cars (300, Sport Fury, and Polara 500) and many Imperials in 1962 and
1963. They are black in color, about 7-8 inches ling, flat for most of
their length, and then flare out at the bottom to form a rounded base.
Please check your old parts cars and parts supply. Thanks for your help.
Mike
[Non-text portions of this message have been removed]
________________________________________________________________________
________________________________________________________________________
Message: 4
Date: Thu, 20 Nov 2003 18:37:49 -0600
From: "Wayne Wunderlich" <texan@xxxxxxxxx>
Subject: 300 models
Hi Group,
Just received a Danbury Mint catalog today with 2 Chrysler 300 models.
1. 1957 Customized 300C Item no. 845-04
2. 1958 300 D Sport Coupe Item No. 430-03
Both are 1:24 scale 9" in length and each cost
$115.00 plus $7.80 shipping.
Phone no: 866-345-5133 they did not show a web site.
Wayne
________________________________________________________________________
________________________________________________________________________
Message: 5
Date: Thu, 20 Nov 2003 18:04:26 -0800
From: "Henry Hopkins" <hhrp@xxxxxxxxxxxxx>
Subject: 60 F grille PIeces Needed
We are restoring an F hardtop. Missing the chrome grille pieces that go
in the center of the grille surround. Three pieces, a verticle piece with
a circle in the center for the 300 medallion and two side pieces, a right
and a left.
Yes, hard to find, I am sure, but asking and hoping someone in the club
might have a spare set around somewhere that we could purchase?????
If so, please get back to us.
Thanks, Henry Hopkins 510-234-9649
[Non-text portions of this message have been removed]
________________________________________________________________________
________________________________________________________________________
Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
<<attachment: winmail.dat>>
Back to the Home of the Forward Look Network
Archive Sitemap